Upgrade blowtorch for Hakko T12 with TaoBao - change display 0.96" by 1.3"

  • Price: $3.73

As promised in the previous review, I will write the process of upgrade of the soldering station (PS) with the STM32 controller - replacing the display 0.96" by 1.3". If anyone is interested in what it turned out to be.
Yandex and guugula discs collected all the firmware I know on the soldering stations, hairdryer and combo 2v1

On TaoWao was found and purchased OLED displays 1.3" with an SPI interface to install on the controller board v2.00. The price in the store was $3.73, taking into account delivery in China to the carrier's warehouse - $4.75.
According to information received from Muskovchanin Denis aka salamatin
if the 2.0 or 2.0S board replaces the OLED display from 0.96 to 1.3, it will work without rewithing
i.e. there should be no problems.
I've had to stop displays and... A miracle didn't happen. The initiation of the new display went well, the controller started. But the display on the right side was a vertical band of 2 pixels wide, and all the information on the display was shifted to the left by these same 2 pixels

If you believe the screenshots from Denis,everything should be fine

Nimnul1979,with the active help of Denis,found out that the problem is in the firmware. Denis used the latest available firmware from developer 2.11when modeling, and nimnul1979 and I have a controller stitched with an outdated version of 2.09 .
It was decided to re-test the PS controller.
STM32 microcontroller will need a st_link v2 softwareer to firmware

The process itself looks like this:
1. Disconnect the PS fee from the power supply.
2. You need to find on the board 4 contacts SWD (V-C-D-G qV, Clock, Data, GND)

3. To make it easier to connect, the connector is hooked to these contacts

but you can even without it, just to snapp the train from the programmer to the board.
4. Install the STM32 ST_Link Utilityprogram, it also tired the driver for st_link v2 .

5.Connect a st_link v2to your computer. If the driver is well established, a new USB device (USB-gt; STM32 STLink) will appear in the Windows Device Manager.
6. Remove the st_link from the USB connector.
7. Connect the PS fee to it through SWD.
8. Connect the st_link to the USB connector. If the SWD contacts are connected correctly (at least V and G), the PS board will start.
9. Run STM32 ST_Link Utility
10. In the Target menu, choose Connect. The STM32 controller must be connected. If you don't connect, check the correct connection of SWD contacts (V-C-D-G).
11. In the Target menu, choose Options bytes. Put Read out Protection in Disabled. We remove the protection from reading.
12. The controller is ready for stitching.
13. In the Target menu, choose Erase Chip. We're erasing the old firmware.
14. Choose Open Fileon the File menu. Choose a new firmware file. For the 2.00 version board it's T12_v.2.00_OLED1.3.hex
15. In the Target menu, choose Programm and Verify - Start. We stitch and check.

Firmware on soldering stations, hairdryer and combo 2v1 take yadisk or google

Now you can take st_link out of the USB connector. The process of re-stitching is complete.
We restart the PS controller by soaking it from the programmer or from the BP.
If all goes well, the microcontroller will start and you will see an invitation to enter the firmware activation code

As Denis explained to me:
You have a very ancient version of the firmware in the soldering iron. And there is an activation somehow different. The author changed the firmware and changed the way the activation was stored. That's why when the firmware version was updated, the code was requested. Because the new version has not found its activation.
I sent Denis ID1 and ID2 of my station to the person, and he sent me the activation codes.
The activation code is entered in a bit by the rotation of the encoder handle

After entering the activation code, restart the controller and see the standard working mode window, BUT in Chinese. To return the English menu, you need to go to the settings and in paragraph 15 and choose the language of the interface.

This is the end of the display replacement process. We gather PS and enjoy the result

Firmware version

In the new firmware menu increased by 2 items:
13. Desolder Mode - Parable Mode
In this menu item, choose:
Valve valve
Inching
14. Pump Setup On Time - Setting the pump time of pump.
This item of the menu adjusts the pump time of the pump (10÷60 seconds).

I have a fee version 2.00, in it these features are not implemented and how they work I can not say. These modes are relevant to the board version 2.0S and 2.1S, there are contacts to connect the pump and valve. If someone decides to implement these modes, then here is the connection scheme (for the information provided thanks to Denis)

There are no contacts on the 2.00 board, but you can try to snapp directly to the feet of STM32.

That's it, the desired result is achieved. How it was and how it became

Using the PS has become more convenient, updated firmware, there is an opportunity to expand the functionality.

Once again I express my special gratitude to Nimnul1979 and salamatin for their ideological inspiration, moral and technical support.

Thank you all for your attention, I look forward to constructive criticism and comments.

P.S. If someone needs to get an activation code to write to Denis ID1 and ID2 from your station, I think it will help you.
I plan to buy +42 Add to favorites +35 +80
Collapse Deploy
Comments(618)
Rss
+
avatar
+13
I will be the first, Sasha as always perfectly wrote, well, as well as thanks to Denis (salamatin) for help, without his support ... wouldn't it make sense to do an update ;)
+
avatar
  • woddy
  • January 15, 2017, 00:44
0
Thank you!
The controller bought on Ali, arrived three days ago. The display needs to be changed unequivocally.
Time does not know when will appear, but the display will order now.

Another question on the topic, maybe who knows. An acquaintance bought a station on Ali ready. The controller is stm32, but all of it is a friend, there are no functions. Is that an old stitch? The seller does not make contact
+
avatar
+2
Show photo boards, maybe it's a clone, boards on STM32
+
avatar
  • woddy
  • 15 января 2017, 09:04
0
www.adslclub.ru/upload/img/2017-01/15-13034214581.jpg menu photo
exactly STM32, sorted out looked.
until he wants to unwind...
+
avatar
  • Totka
  • March 24, 2018, 05:27
+1
Here's a youtube review:
www.youtube.com/watch?v=n8pu6du0ftY&feature=youtu.be

Here's the fee:
i.imgur.com/dqWMbfQ.jpg

Here's the diagram:
www.ptdreamer.com/wp-content/uploads/2018/02/iron_schematic.png

Here's a guide to firmware (3 pages, down there on the following page):
www.ptdreamer.com/chinese-stm32-oled-soldering-controller-reverse-engineer-custom-firmware/

Here's the firmware- the rest:
github.com/PTDreamer/stm32_soldering_iron_controller

And here's a video of the firmware work:
www.youtube.com/watch?v=g3d1rZa-i5M

and a guide on YouTube:
www.youtube.com/watch?v=dzN0QhjiP0Y

There are 3 versions such as "3.5," "4.0s" and generally where there is no version (auto-disconnecting option - the number of minutes when the screensaver turns on before shaking the ball and then the usual mode). And in fact it is at1.5, on the alishka is also by the way. And in the guide it is written that the slink should be there at 103 under 103 turns out, that is, you need to take a "mini stlink in2" on the ebay or ali. And two types of displays, of course.
+
avatar
+1
You already have quite a lot of info - can the view cloud on this controller?
+
avatar
  • Totka
  • March 25, 2018, 7:36 p.m.
+2
So I noticed yesterday that the reviewer appeared:
mysku.ru/blog/china-stores/61541.html

There's a slightly older model, but the boards are identical.

Just on ali it stands:
aliexpress.com/item/STM32-OLED-V3-5-OLED-Screen-Size-1-3-T12-Soldering-Station-Temperature-Control-Board-Electric/32821308037.html
a little cheaper without reviews seen (but still 45-48 dollars).

Here's a link where I took:
item.taobao.com/item.htm?&id=537608087681
it is still expensive (the weighting is not very large, but will come out as on ali, except that the quality is higher will be)

BP is so good, but the capacitors are noding and the throttle is buzzing - who needs this music at work? For exactly the same money there are normal 5 contact solders on the 2.1 version.

Although if you finish the firmware (fonts, graphics, Russian to do - still without problems implemented) and the 5th wire to use under the temperature of the room, at the same time to put a normal handle type
mysku.ru/blog/taobao/59301.html
it's quite a good device.

But here's to advise to buy version 1.5, when there is 2.1 for less money - let's just say the solution is not very successful. Who has already bought - let them overdo it, soon I think a couple of guides in the comments will appear. So far, there is no finished firmware with a superior 2.1 version of functionality (I would like a large graphic font on the current temperature). The "bust" function at a given time to set a new temperature - so it is easier for me to twist the encoder with my fingers than to press a button, because the soldering iron can go forward.
+
avatar
+1
So no one prevents to make his review and tell there is not a fable about a friend and his wife, and normally paint the controller, its element base, firmware, alternative firmware, about BP not to forget, all this to complement the references to Ali and Tao and now ready a normal review.

Honor and called the author for the work done ;-)

PS do not be afraid to pee, at first it is difficult, takes a lot of time, then you get involved ;-)
and you'll be like Kirich scribbling one by one
+
avatar
+1
I'll support the interface! I liked from this project dangerousprototypes.com/forum/viewtopic.php?f=56&t=7218 and video www.youtube.com/watch?v=-f0KSU0PJzc&t=70s but in programming is not strong ...
+
avatar
  • Totka
  • May 2, 2018, 03:02
0
Well, by the way, the author is finalizing the firmware.

Vaughn made under 1.3 inch displays (admittedly crooked).

i.imgur.com/QeJvClG.jpg

The font is slightly increased (rather more important is not the change of the font itself, but that the source code (in commits) you can understand where and what to change you need, although probably there is everything in the studio, never worked in it).

But again,25, the current temperature is elephant-like, but the desired temperature is barely visible. In general, it would be nice to make a competent interface under 1.3, can give the Russian language to add.

I slipped easily with a normal line with 103 on board, 4 pin-wires Mom-Dad did not even let up, and just under the lever fixed on contact. Shil on the guide from the YouTube channel of the author of the firmware, although there from the guide only required 2 pina as called, because the food and ground on the board are marked on the top side, so that the display is not removed, and directly so and sew.
Took here:
«1PC mini ST-LINK/V2 ST LINK STLINK STM8 STM32 emulator download super protection»
ru.aliexpress.com/item/1PC-mini-ST-LINK-V2-ST-LINK-STLINK-STM8-STM32-emulator-download-super-protection/32661136538.html

If you take, then buy a link where pins stick out upstairs and the link itself looks naked. In the comments to the order asked for the 103rd, so and came, although there all comes 103 lately. Moreover, the link is caught in the film from statics and CK, too, not bad. And the links that are like a flash drive or with horizontal pins - those on the 101st.

In general, from the fact of the STC-shnaya solder turned out a normal polygamous station without problems with the evaporation of the flux when replacing the sting (immediately remove those stings and create new, then each calibrate first choosing a stinger, then calibration, but be prepared for 450-460 degrees for a couple of seconds), and then the station somehow wanted and 550 degrees to stick with the fool, but I turned it off. Even maybe the author will correct something, or then a couple of joints is available.
+
avatar
0
Is it really STM32?
Maybe there's STC...
+
avatar
0
Exactly. I have the same STM32, and all the menus are like on STC. I can get in there tomorrow and take a picture if I have to.
He's also interested in re-stitching.
+
avatar
0
We have to compare the schemes...
+
avatar
  • qwerty2
  • 15 января 2017, 14:21
0
The 103-line processor is fatter than we all are. Where did the controller get purchased?
+
avatar
  • Kvi
  • 15 января 2017, 15:02
+2
I'm not thrilled with the scheme:
1. No external memory. That is, there is no way to create a library of stings and their calibration.
2. The cold-sleeping temperature is again shoved not to the point of the thermopapa, but to the inside of the case, where it will show the temperature of the power supply.
3. There are no real-time hours. But I will not refuse - hours in the workplace.

To power the MCP6002 had to be made DC-DC. What's the point? Couldn't have been done like this review controller?
In general, the scheme is more complicated, and the functionality is poorer. It's more expensive.
+
avatar
  • qwerty2
  • 15 января 2017, 15:35
0
The library, like all settings, can be stored in a flush. There is a real-time watch in the chip.
I wanted to change the chip to 103 just because of the USB.
+
avatar
  • Kvi
  • 15 января 2017, 16:43
+2
There is a real-time watch in the chip.
There's a chip in it. But there's no board. There's not even a place for watch kvart. Accordingly, and in the software.
I wanted to change the chip to 103 just because of USB
And what is necessarily USB? What does StLink do not like for $2?
+
avatar
  • qwerty2
  • 15 января 2017, 16:57
0
the battery-powered quartz can be squiszled. About the software is clear, you just talked about the scheme.
USB was planned to control the station from the comp. Before the advent of the people's controller, he conceived his software to write.
+
avatar
+1
Saw on Ali and Tao this controller, did not buy, because the thermosensor measures the temperature on Mars and the parameters did not like.
I can call, but it would be easier to compare with the scheme.
Well, ask the developer about the scheme.
Or here's yadi.sk/d/BK2hbLeb37jRXd
+
avatar
0
I agree. I actually bought it by mistake, too. But since the mistake was mine, I did not argue. I'd just buy a normal controller, but there's also a different knob. That is, you will have to buy a controller and a new pen. As long as the toad suffocates - like and so works :)
+
avatar
+2
There is nothing terrible, try to work on it and there you decide whether you need it, will be small, sell and buy this ;)
+
avatar
0
Good and well for all!
Dear An_private, tell me how you have a connected pen in the station, I ordered the same controller version 3.5 with a fool. Now I'm breaking my head as a five-engine, blue handle, because the controller has only 4 contacts. The power was sorted out, but where the sensor and the termistor to tulat??? Please help.
+
avatar
+1
And the hell knows it - how it's connected :) I didn't know how to connect. Try to contact the store manager - can help. Did they take it here?
aliexpress.com/store/product/STM32-OLED-V3-5-OLED-T12-Soldering-Station-Temperature-Control-Board-1-3-Size-Screen-OLED/918038_32822843496.html
There the manager is normally in contact, so that can and will help.
+
avatar
-1
I did. He wrote me something about 4 contacts, but I didn't pay attention to it! I thought what's smart, then I had no idea how it works this "Hakko T12".

And it works like this (quote) - "It turns out that the thermopara and heater are simply steamed together. Then I took a thermopara from the multimeter and measured its resistance, it turned out to be about 16 - 17 Om - that's where the dog is buried! If you take the fact that the heater has resistance of about 3 Om in a cold state (as with HAKKO heaters), then when serving the heat, the whole current takes away the heater. The job of electronics is to turn off the heater at the right time and remove the readings from the thermopar."

If the dear gentlemen reviewers told about it in detail, I think I would have chosen a controller with version 2.1s, and so behaved like a deer on the Russian language menu ...
+
avatar
  • adjuster
  • 08 декабря 2017, 17:35
-1
It is also not clear why in the set to the controller and to the handle the seller lays the termistor, I now have two - how a small stabilizer looks on 10kOm and on the board one as a black drop???
+
avatar
0
It turns out that the thermopara and heater are simply steamed together.
Delirium, thermopara and heater in the cartridge are connected sequentially, in the innet (and here on the musket) the infa and photo of the smoky sting is.
If the dear gentlemen, the reviewers would have told about it in detail
What's it about?
About version 3.5?
When the review was written, this undercontroller was not there yet.
And comments to reviews read to you faith does not allow, about v3.5 has long been known, a lot of negative comments. Read carefully.

And what prevents you from doing a review on this controller?
Comment is hidden

+
avatar
  • adjuster
  • 08 декабря 2017, 22:42
0


+
avatar
0
I understand correctly that if some people there do not send the activation code, then we have a brick?))
Maybe you should have drained the old firmware before erasing it?
+
avatar
+1
There's a protection for reading worth it.
won't send the activation code, then we have a brick?))
Who prevents you from writing in person and asking?
+
avatar
  • Kvi
  • 15 января 2017, 14:40
+1
Are you sure you can merge with STM?
And no one makes you addicted to "some brow."
Pay money to the Chinese and use the "factory" firmware.
+
avatar
+2
I had the protection turned off, with the connect with the stem, immediately considered firmware. Some people there always helps... believe me as the first to pass ;)
+
avatar
  • qwerty2
  • 15 января 2017, 15:39
0
Is the activation flag stored in a chip or in an e-20?
+
avatar
+2
In the chip, I didn't have to go to the SWD ;)
+
avatar
  • qwerty2
  • 15 января 2017, 16:36
0
So you didn't seem to write that when you restore the firmware on the same chip, the activation does not fly off. That's why I asked about the place where the flag was stored.
+
avatar
  • Kvi
  • 15 января 2017, 16:38
+1
Depends on what's the flag. The key lies in her dressing room. The key is unique, tied to a particular STM crystal. At the start of the program the key is read and, if it is valid, the program is loaded further. Otherwise, you need to enter ID.
+
avatar
+2
Denis said that at 2.11 the code is stored in the open-market and subsequent transitions the code will not fly and on 2.09 will fly after the firmware.
+
avatar
+4
These indicators have two types of controllers.
The main differences: this is the shift by two points and the maximum brightness, the maximum current per point differs twice. Different instructions for turning on/off the built-in pumping.
There are also no scrolls, but almost no one uses it.
It is treated at the level of initialization and replacement of the tocosing resistor, then the code in principle can not be touched.
+
avatar
+2
Thanks for the explanations, but the author took it into account in firmware 2.11, so it is more useful to sew and there the case of each ;)
+
avatar
  • bazilio
  • 27 марта 2017, 04:06
0
I seem to have got on display with this Chinese woman saleswoman, and they all apparently do not care that putting in the parcel the main difference color blue and white ... the main thing to sell.

before me, she sent to the buyer with a jammed display and probably did not have such a problem, and I was asked before sending it will be with a white display ... but it never occurred to me that it might not be compatible...

I read the article, but the controller is a different version of firmware 1.3, I realized that maybe it put the display from the predictive version...

aliexpress.com/store/product/T12-OLED-Display-DIY-Kits-T12-Electronic-Soldering-Iron-TipsTemperature-Controller-Wake-Sleep-Shock-110-240v/1486111_32786936747.html

look can this be corrected? I don't really know all about this firmware kitchen, etc. Where to look for them...

You have to decide whether to open a dispute with the seller and what to demand from him!?



+
avatar
+2
I understand you have a fee from WOKA, it's a firmware different from the firmware presented here.
Open the debate return the money
+
avatar
  • m13ale
  • 15 января 2017, 01:58
-4
Comment is hidden

+
avatar
+4
Of course you can... But
1. This article is about the upgrade of the finished device.
2. Do always have something ;)
3. You with the size of the unisolder is not what not confused? (128x64 OLED display with rich user interface.)
4. More settings... where in unisolder? there's an emphasis on versatility in soldering iron, and now count how much it will come out for you and you will make it in the manufacture? clearly more expensive will turn out.
www.youtube.com/watch?v=pw5_ZdChZXM
Comment is hidden

+
avatar
+1
I wonder what you say about the modelists who put tens or a hundred bucks in their "toys"?
+
avatar
+3
Thanks for the review, the dog has become more solid. Just don't know what a terrible secret behind the seven activation seals, why can't they be published here? Or everyone to bow to Denis!?
+
avatar
  • tianddu
  • 15 января 2017, 08:08
0
Apparently every aidi has its own key, isn't it?
+
avatar
0
Or maybe :).
+
avatar
+4
Exactly, and the developer (Chinese) does not go to contact and the codes do not give.
Denis was able to create a keigen - if anyone needs help.
+
avatar
0
Why didn't he lay out the keygen? it still sends codes for free. or not all for free?))
+
avatar
  • Kartus
  • 15 января 2017, 11:49
+6
Well, first of all, if the keygen is laid out, the Chinese will check it and change the algorithm - he is not a fool. And secondly, the one who will invent the gene and dance as he wants)))
+
avatar
  • Kvi
  • 15 января 2017, 14:43
+3
Why can't you do the keigen and lay it out? I've got it laid out here. It's something to disassemble, to understand someone else's code, to write a keygen.
You'll do it and lay it out. You can even make money, you'll get rich.
+
avatar
-1
Why would I do that? I don't know about it, and I don't see the point in dealing with money or money.
+
avatar
-10
+
avatar
  • tklim
  • 15 января 2017, 08:23
+7
That is, the fact that you are an external unit in which the BP, controller, display and controls call "controller" - do not bother you?
+
avatar
-7
+
avatar
  • Kvi
  • 15 января 2017, 08:59
0
And why "Solony" 20 years ago called soldering stations? There's only a transformer and a little handkerchief inside, isn't it?
+
avatar
  • tianddu
  • 15 января 2017, 08:09
+1
Who edozing the controller on stm32 for the hairdryer? Or something different for a hairdryer? For a soldering controller waiting, still would like a good controller for the hairdryer.
+
avatar
+4
Wait, there will be a review
+
avatar
0
we're still waiting and we're not losing hope
+
avatar
+3
Everything is already there, but there is not enough time, once we collect, there will be a review of the ;)
+
avatar
  • bazilio
  • 17 января 2017, 04:48
0
And what is this controller, the price, where bought?
+
avatar
+2
+
avatar
+10
I use this option

+
avatar
+1
Buying ready or collecting?
+
avatar
0
No, the finished took, there is a board of soldering and hair dryer combined in one, the version of the firmware that's just do not understand, on the display like all the same and the number that old, in the menu 17 items
+
avatar
  • fafhrd
  • 15 января 2017, 10:55
0
1 How to calibrate the sting? does not warm up the landfills.
2 Drink coil advise? If not offline bought...
+
avatar
0
In the face
+
avatar
  • DDimann
  • 15 января 2017, 09:48
0
I didn't look for it on purpose, but I got one on tao. True, only the body. :)
Is there just between the soldering connector and the hairdryer cord a hole for the vacuum tweezer fitting?
+
avatar
+1
yes, the hole under this case, but there's nothing in the kit, the seller's page says on my own that goes apart,
https://world.taobao.com/item/521250763857.htm
+
avatar
+2
There is also a case separately
There is also a kit for assembly,there is also a ready-made station
+
avatar
  • bazilio
  • 17 января 2017, 04:15
0
strange - why don't they sell on ALI!?
+
avatar
+1
as I understood this exclusive option and not everyone available
+
avatar
+1
So Ali is not all that is on Tao sell
And the prices for Ali are not particularly happy.
The same blowtorch on STM32 in different versions (at least 4) on Tao has been sold for more than a year, and Ali only at the end of the summer began to appear after the review of Allary1980
It is quite possible, as the review of the hairdryer will take place, and on Ali on sale will appear its controllers.
The same goes for these combines... But they and Tao are not cheap, on Ali the price in general will be the PPC
+
avatar
0
here I am about the same, a few thousand price above will be 100%
+
avatar
0
Ali, there are brains from these stations.
The drinker is a hairdryer. (a set of two boards, controllers, power boards). Board power version 1.0, board controller version 1.1 (seen)
or each fee individually
There's a separate hairdryer.
+
avatar
+2
Well, yes, the price of "SUPER"is no big deal.
Tao - $26.43 - https://world.taobao.com/item/521250763857.htm
Ali - $54.29 - almost twice as expensive

I don't think two-board delivery will cost $20
+
avatar
  • bazilio
  • 19 января 2017, 21:15
0
Yes, this Shenzhen SIE Electrical Technology Co., Ltd hairdryer costs 3,761.33 rubles... The look of a conventional hairdryer can inside something wrong...
+
avatar
+1
not, not the usual Chinese, and what is a little better but also Chinese, outwardly the difference in the enclosures and fastenings of the nozzles
shenzhen is lower than Shenzhen
item.taobao.com/item.htm?spm=a312a.7728556.w4023-10625948426.10.2G8QOS&id=527897094094
+
avatar
  • bazilio
  • 19 января 2017, 21:28
0
I was thinking. . . . in such combines Ahilesov's heel - God forbid to happen - no solder, no hairdryer will not be at once - stone then one for all ...

first review of the hairdryer aliexpress.com/item/Hot-Air-Gun-Soldering-Station-Controller-STM32-Solder-Iron-Soldering-Handle-Nozzle-Station-DIY-Electric-Power/32774114750.html

No build instructions, no instructions to use (and the default language is Chinese. controller: There is a time indicator, but neither the current time nor the opening time displays. No calibration of the thermopapa (with my hairdryer the temperature on the exit on the controller differs by 100!!! degrees from the real) seller-large order, made a small discount, sent quickly, the packaging is good. I apologized for the shobs, I couldn't help it any more.
+
avatar
+1
PPC prices
+
avatar
-1
in the scheduly of the kit on the combain in principle is not expensive and the delivery type is free, on tao a little cheaper but you need to pay that fifth., then it will turn out, as I am so better on ali to buy, as regards the combine as I have
+
avatar
+2
Something of this review is no longer, either the person who wrote it has already figured it out, or the Chinese removes the reviews :(
+
avatar
+1
just looked there
+
avatar
+2
Yes, I haven't seen it, there's a review (((well, when I'll collect my... I'll check it out.
+
avatar
+1
Well fig take off, will burn on the separation of fees, or the same set
+
avatar
  • Elbregs
  • 22 января 2017, 10:39
0
It's a good sell: aliexpress.com/item/OLED-Hot-Air-Gun-Soldering-Station-DIY-Electric-Power-Tools-STM32-Controller-Combo-Soldering-Iron-T12/32791527622.html
And it looks like from the station from the photos above.
I wanted to take, but given that I already have a station on the "people's" controller, the station on STM32F101 v2.0, plus lies the controller on STM32F103 v1.5 (photo of such a board is higher), which I sent by mistake the Chinese, it will be a bust. But separately the controller for the hairdryer will buy a little later, when the prices will be adequate.
+
avatar
0
it doesn't look like it, and it is, pictures of my combine
+
avatar
  • bazilio
  • 22 января 2017, 17:03
0
lies the controller on STM32F103 v1.5 (photo of such a board is above),
I didn't understand what kind of controller it was... Above is just a photo of the station and a bunch of links...

I've only found v1.3 on STM32F103

And I would like to understand what kind of controller it is!
+
avatar
  • Elbregs
  • 23 января 2017, 09:01
+2
Here's a link to the controller: aliexpress.com/store/product/The-latest-Version-of-OLED-Soldering-Station-Control-Panel-STM32-edition-OLED-Screen-Control-Panel-Electric/918038_32706564155.html
Here are the photos: mysku.ru/blog/taobao/48640.html#comment1863803
Controversial controller: on the one hand, a more powerful processor, power dc/DC - linenik (not warmed unlike clean linen, which falls 20B and dissipates about 2.5W); on the other hand, the circuit curve of the board, the NTC is split on the board, there is no external memory, and the overall functionality of the firmware is no more than the "people's controller".
I do not recommend to buy.
+
avatar
+4
This controller sucks!
I don't recommend buying under any circumstances
Elbregs is right. This is a completely different development, with the review here and there in the review discussion nothing in common.
Yes, the STM32F103 controller is more powerful, but the functionality as in the pre-flood Chinese STC with LED indicator - useless development.
+
avatar
  • FraY
  • 12 марта 2017, 13:35
0
Can you look inside what transistors are on the control of the phen meter and on which leg the stmki controls? Bought only a controller board and now screw soldering iron and hair dryer
+
avatar
0
I don't know about it, so I'm not going to help.
+
avatar
  • FraY
  • 12 марта 2017, 19:23
0
And a picture of the fee in parts?
+
avatar
0
there is a lot of analysis and there is no time, combo almost constantly in work, look do not promise
+
avatar
  • tklim
  • 15 января 2017, 08:33
+6
I didn't understand... It was a review of Denis or the soldering station or the actual display?
14. Choose Open File on the File menu. Choose a new firmware file. For the 2.00 version board it's T12_HW20_Encryption_OLED13.hex
You could attach the firmware file... And then the meaning of this whole narrative is lost.
P.S. have nothing against Denis,do not know who it is, but probably a good man ;)
+
avatar
0
Then you should immediately ask and kagen to apply. And in general, the whole set of available firmware. But there is a risk that the Chinese sniff and strengthen the protection.
And another huge question - whether respected comrades will want to share with all honest people their achievements, and not only with knocked in person.
+
avatar
  • tklim
  • 15 января 2017, 09:49
+1
Yes you are right. And for sure, not many people will want to repeat. Taobao-intermediaries-re-activation - too many actions, and the result is questionable. And the most important photo "was-became" made from different distances - does not make it clear whether it has become much better
+
avatar
0
And the most important photo "was-became" made from different distances - does not make it clear whether it has become much better
The same me... only in profile, all this idea with the replacement of the display just out of boredom and the presence of extra money, it does not affect the functionality.
+
avatar
  • Kvi
  • 15 января 2017, 14:45
+2
I don't agree. My eyes are not the same as I get older. And the bigger display won't hurt.
+
avatar
+1
Okay, now I'm looking at my 0.96 display and I'm not steaming at all, I've been wearing glasses for 20 years. And honestly do not understand why constantly stare at the display, there cartoons do not show. Is it really how big it is?
+
avatar
  • Kvi
  • 15 января 2017, 15:03
+1
My display will come, I'll put it. Then I'll show :).
+
avatar
0
That's when we'll see if sheepskin is worth dressing;)
+
avatar
+3
Well really white color looks cool, and if the front panel is milling under a 1.3 display, why not :)
+
avatar
0
Of course it's cool. but that's just how it's related to
Updated firmware, there is an opportunity to expand the functionality.
I don't understand
+
avatar
+1
Menu 13, 14 items
+
avatar
-2
This is understandable, but has nothing to do with replacing the display
+
avatar
+2
There was an attempt to change the screen, it did not work, they were blocked, we got more opportunities to refine... How else can you explain?
+
avatar
+2
it was meant to finish the controller and be able to work with a dismantling gun from Hakko
+
avatar
  • Kvi
  • 15 января 2017, 16:50
+1
If you do not want to overs shave STM, and you want to replace the display, you can just try to mix the glass itself. In an earlier review, this was described.
By the way. How is it with the accuracy of the clock on the new firmware? Is it also sad?
+
avatar
+2
I've deliberately reduced the clock second to second, so I'd see what the move is. I'm more interested in adjusting whether it works or not, because the software clock... no matter how the standard is exactly, that would be the DS3231, but this "fence" is not for this controller ;)
+
avatar
  • Kvi
  • 15 января 2017, 17:13
+2
this "fence" is not for this controller ;)
Why else? The DS3231 has a output of 32768, and the STM (according to the date) allows external synchronization on one of the quartz legs. I ordered my own headscarves aliexpress.com/item/Free-shipping-DS3231-Real-Time-Clock-Module-for-arduino-3-3V-5V-with-battery-For-Raspberry/32332523866.html. If they come, I'll experiment.
+
avatar
+2
Thanks for the link, cool headscarves, you have to order yourself.
About the watch in the controller... I'm not good... But it's IMHO.
+
avatar
+1
it's not a fact that it's going to work. There are different controllers on the boards:
0.96 SSD1306, 1.3 S1106.
In an earlier review, this was described.
0.96 batted by 0.96
+
avatar
  • Kvi
  • 15 января 2017, 08:56
+2
While waiting for the parcel with Ali with the display and StLink. And then the ready-made instruction on a platter :)
Thanks to the author.
As for the decsoldering - I wonder what "gun" was supposed to be?
+
avatar
+1
I looked at Tao "pistols" - the price is not formed.
+
avatar
  • dens17
  • 15 января 2017, 09:01
0
Recently, there was a review - mysku.ru/blog/aliexpress/48118.html
The seller on Ali, from the review, at the request of workers immediately throws in the kit 1.3" display.
+
avatar
+2
changes and throws in the price
There is no free cheese
+
avatar
  • DDimann
  • 15 января 2017, 09:26
0
Normal upgrade, plus.
And the question: on the penultimate photo, where the connection of the pump/valve, these contacts - 7 pieces. Well, one is clearly the land, and there is no information about the rest?
And then I have just 2.1s like a house lies ...
+
avatar
+1
If I'm not mistaken, there's some of the contacts duplicate encoder, look at the board
+
avatar
  • Kvi
  • 15 января 2017, 09:45
0
I'd assume it's a gun control button. That is, while the encoder is spinning - the management of the soldering iron. And if it's just a circuit (one contact or two at a time (which is likely)), then the valve "sucker" is triggered. I don't see any other gun control.
+
avatar
+3
There are very few infus, we have to dig China-innet
+
avatar
  • Kvi
  • 15 января 2017, 16:45
+2
And it can be very even.
+
avatar
+3
+
avatar
+2
I don't think the price will be too good.
https://world.taobao.com/item/5256889353.htm
USD 260.56
+
avatar
+1
There is an "underwater stone" pump that will create this dilution of air, too, you need not cheap, because the length of the tube to the gun itself tank,need a normal "pull" and our body is small for this, you need to make a separate controller in a separate body ;)
+
avatar
+4
Added a link to firmware in the review.
+
avatar
  • R0m4ig
  • 15 января 2017, 13:09
0
Friends, a little out of touch, but I'm asking for help.
The second day I can't get into Taobao. When you press the buy button gives out such an error that on the product page that of the basket. I registered recently, I haven't bought anything yet. The profile is completely filled out. Tried to go to that address but does not write any mistakes there. Who has ever faced such a thing? Google is silent.

+
avatar
  • R0m4ig
  • 15 января 2017, 14:27
-1
A new acc, everything was stabbed.
But I wonder what's wrong with the old one?)
+
avatar
  • Aleg
  • 15 января 2017, 13:18
0
I'm not really in the topic, so there was a question off topic:
set costs $40, and ready $140?
+
avatar
  • aarg
  • 15 января 2017, 15:51
0
it's probably for a cool pen of that kind of money
+
avatar
+2
set costs $40, and ready $140?
cool stand and handle
https://world.taobao.com/item/43610751726.htm
Kit costs USD 22.74
+
avatar
+4
It's not a cool pen yet, but Cannon is in metal, that's a cool... Think of carbon, maybe it's not there, just pasted with film under carbon.
https://world.taobao.com/item/536318332207.htm
+
avatar
+1
tell me what is used as a solder suction? Some kind of solenoid? And this vacuum pump is this tweezers?
+
avatar
  • Kvi
  • 15 января 2017, 14:48
+3
Most likely, the pump creates discharge in the tank, and the solenoid opens the valve during the "sucking" of the heated solder. An analogue of a spring piston. But I can make a mistake - I have not seen live. Just a diagram.
+
avatar
0
That's terribly interesting. Once there was a station with Solomon suction. Just pulling the pump as the trigger is pulled. Yes and the sting of T12 desolder probably should be
I saw Ali's saw the saw-off sawers with a large salt-watering one that created a suction discharge.
+
avatar
0
I have a 2.0 version controller and a 2.09 version, a st link and a hairdryer. Can someone suggest a link to a suitable display for such a rework only on Ali.
+
avatar
+1
I only have links to Tao:
soldering iron - https://world.taobao.com/item/530763498769.htm
hairdryer - https://world.taobao.com/item/530763650699.htm
look at the models, look for Ali
These have already been tested
+
avatar
  • Kvi
  • 15 января 2017, 21:48
0
I ordered myself this: aliexpress.com/item/1PCS-1-3-OLED-module-white-color-SPI-128X64-1-3-inch-OLED-LCD-LED-Display/32684364078.html
I'm waiting.
You don't need a hairdryer when you replace it. And for the firmware of the chip, the contacts on the board are displayed.
+
avatar
+1
There's a 7-pin connector on the controller board v.2.00 - 6
You'll need to connect correctly
Look here and there
+
avatar
  • Kvi
  • 15 января 2017, 22:10
0
Look here and there
I've read it before. "Version 2.0 (SPI interface). I have a display of 7 legs, an extra output CS hung on the ground" - that's why ordered.
+
avatar
+1
It's for Bird1833
+
avatar
  • mich82
  • 05 марта 2019, 00:48
0
please, ID1:3438, ID2:1494 HELP ME RG1:xxxx AND RG2:xxxx
+
avatar
+1
If it's for a blowtorch, then
RG1: 6A4B
RG2: DC5B
+
avatar
0
Tell me, please. Board 2.0 firmware 2.09
If you put a display of voltage shows the temperature on Mars...
No handle 24.8- 0.1 with handle 18.5-0.5
Although the power supply is powerful and on it exactly 24 that with a load that without. Connected several lab technicians the result is the same.

The question is everyone's right?
Is switching to a new firmware solves the problem?
Thank you.
+
avatar
  • Kvi
  • 17 января 2017, 12:59
0
Is switching to a new firmware solves the problem?
No. The 2.0 board is physically short of the parts through which the STM must measure the power supply voltage.
I wrote somewhere in one of the reviews of STM controllers. In the following versions, these resistors are added.
+
avatar
+2
If I'm not mistaken, you have to make a divider on 18 legs.
mysku.ru/blog/aliexpress/48118.html#comment1831361
salamatin wrote:
At 2.00, the voltage from the divider should come on 18 legs (B0). I checked on the firmware version 2.11, I don't have another one. The rubber-like divider has a 10K upper shoulder, 1K lower shoulder and ceramics so as not to gallop the readings.
+
avatar
+2
Welcome to everyone. This is the kind of controller aliexpress.com/item/STM32-Edition-OLED-T12-Intelligent-Electric-Iron-Temperature-Welding-Units-Electronic-Soldering-Wake-Sleep-Shock-110/32766679896.html,but the seller sent a controller with a small 0.96" display, and was ordered with a large 1.3." In the process of correspondence, the seller promised to send the desired display at the next order, so it was done. The seller didn't cheat. The display module is not a problem, but there was a problem of not matching firmware to different sizes of displays. When you turn on the controller, the picture is like the beginning of the view, with a vertical strip of 2 pixels. The seller's appeals about the problem were not addressed, the answer was that this controller does not fit the 1.3" display. Here this review came in handy. One BUT, no programmer. The programor was ordered, but the wait for 30 days forced to look for an alternative. But on the expanse of the innet there was an alternative version of firmware of this controller, which I took advantage of. 2.11 code doesn't fly off after firmware under the new display. In the end, it all ended well.
+
avatar
  • Tangar
  • 20 января 2017, 10:51
0
Well, you said "A" and say "B" - what alternative version of the firmware found, what firmware itself, whether you need to enter the activation code. For me, the topic is relevant, rides the same controller.
+
avatar
+3
When you go from 2.09 to 2.11, the code will be erased because it was stored in the controller and in the new firmware 2.11 the code is stored in the EPROMk.
+
avatar
+7
What was, said "A," I say and "B" in the controller STM32 has its loader. Description on the link chipspace.ru/stm32-bootloader-flash-loader-demonstrator/. here is a full description of the whole process, for a full understanding of the link easystm32.ru/useful-things/42-bootloader-stm3. on the controller you need to drop 44 (BOOT0) the controller's leg from the total wire, and apply a power voltage of 3.3B (thus put the controller into recording mode). To nip the wiring to 30 (TX) and 31 (RX) controller findings to send appropriate signals to them. , I used the FT232RL chip because it already has a 3.3 volt stabilizer built in. bought from the CHIP and DIP store. The micros cesswe is minimal with all air mounting. After firmware 44 output the controller to seal into place. it's going to be like this. I apologize for the welter of comments. Thank you for understanding!!! I didn't have to enter any code. The 2.1S board audit, but firmware 2.11, was under display of 0.96." Firmware 2.11 under the display 1.3" took on the link which is available in the review.
+
avatar
+6
Well, that's right.
firmware before the re-stitching was 2.11, as Nimnul1979 wrote:
in the new firmware 2.11, the code is stored in the EPROMka.
You've changed 2.11 to 2.11 - you don't need to enter the activation code.
The code is needed when moving from 2.09 to 2.11
+
avatar
0
The question is to you and to the rest of the existing owners of PS on iron v 2.1s.
Is your PS watch kit included?

There's a battery in this set.
By the way, but in such and in most sets of batteries there is no battery
.

Who knows (or can at the specifications of the chip to understand/see) what voltage the battery should be. At first glance it seems 2032 on 3B (presumption) I think craftsmen will not be difficult.
+
avatar
0
+
avatar
+3
Any battery on 3B
you can 2032 from the notes, you can do it yourself - not fundamentally
+
avatar
+2
Ordered on the link aliexpress.com/item/STM32-Edition-OLED-T12-Intelligent-Electric-Iron-Temperature-Welding-Units-Electronic-Soldering-Wake-Sleep-Shock-110/32766679896.html Battery wasin the package so that by the way to say the information on the store is not correct.
+
avatar
0
Excuse me, can you check the markings? stm32f103cb written???
+
avatar
0
I bought A-aliexpress.com/item/New-220V-OLED-T12-Digital-Soldering-Iron-Station-Temperature-Controller-72W-With-EU-Plug-T12-Handle/32674414332.html "
I plan to use in modeling for rations of photo-poisoning. The minimum temperature is 150. It should be lowered, preferably to 50. I don't have a boom boom in electronics myself. Was on Savilovsky and in Mitino, no one takes and does not even repair, broke down - buy a new one. Tell me, where can I turn in Moscow with this question?
+
avatar
+1
This is UG on the outdated Chinese STC controller.
Nothing to do with the considered here and here.
no one takes and does not even repair, broke - buy a new one.
What did you want? It's a miracle of Chinese engineering, no one will repair it here, except that BP can look.

P.S. Buying on Ali, Tao, etc. ready soldering stations need not to chase cheapness, but at least a little in the topic to understand ...
+
avatar
0
For my tasks and this one by the eyes. This is my first soldering station. Repairs are interested in reducing the temperature. That's how it works. And still, is it possible to reduce the minimum temperature on it? This is necessary for the use of solders with different melting temperatures (Wood, Rose), collecting a small part consisting of several even smaller ones.
Here's a link to an example of a worthwhile task www.tigerscorner.ru/index.php?topic=1343.345.
Made by the usual soldering iron light. This is taken, so to speak, on trial and for the future because of the range of inexpensive stings and the possibility of temperature adjustment. Ideally, I would like to reduce the minimum. Perhaps one of the forum participants would help me?
+
avatar
+1
And still, is it possible to reduce the minimum temperature on it?
It's all in the firmware, and it's not there.
+
avatar
0
because of the range of inexpensive stings
ага тайская подделка сравнительно с оригиналом не дорога, учитывая цены на б/у жала, средняя цена около рубля
+
avatar
  • oleg_s
  • 11 марта 2017, 21:17
0
Кто знает, подскажите, пожалуйста, какого номинала установлен термистор в ручке.
Знаю, что NTC MF58, а вот какого он номинала?
+
avatar
+3
10K
+
avatar
  • oleg_s
  • 11 марта 2017, 22:48
0
Спасибо большое!
+
avatar
  • oleg_s
  • 12 марта 2017, 06:41
0
Помогите, пожалуйста, определиться с контроллером. На Али есть несколько лотов с ценами от $25 до $40. На вид они для меня одинаковые. Можно бы было определиться по цене, но уж больно разброс большой. Можно бы было спросить у продавца, но для того чтобы спрашивать нужно разбираться в вопросе, а я пока в нем плаваю. Пока научился отличать STM32 от STC. Итак, мне бы хотелось STM32 с 1.3” OLED. Вот что нашел.

aliexpress.com/item/New-Arrival-1-3-STM32-OLED-Soldering-Station-Controller-OLED-Station-Case-OLED-Soldering-Handle-With/32776347540.html

aliexpress.com/store/product/Upgraded-Version-T12-STM32-OLED-Controller-For-24V-Power-Supply-T12-Solder-Soldering-Handle-Soldering-Iron/918038_32789654280.html

And here for $25.

aliexpress.com/item/T12-K-T12-ILS-BC2-BL-STM32-OLED-Controller-Soldering-Handle-Station-Cover-Case-T12-Soldering/32783588410.html
+
avatar
+2
On the first link the fee version 2.0 with a display of 1.3, compared to Tao price is more than 2 times
On the second link the fee version 2.1S with a display of 1.3, compared to Tao price zadrana 2 times
In the third link, the 1.0 version board with 1.3 display is an out-of-date option.

Think you need it?????
+
avatar
  • oleg_s
  • 12 марта 2017, 13:10
0
YOU need it?????
What do you mean? Are these all old versions? Do you need to look for something newer?
+
avatar
+1
look for an opportunity to buy on Tao, save a lot of money
+
avatar
  • oleg_s
  • 12 марта 2017, 14:28
0
Please answer, how much will it cost me to buy one controller per tao? (including the services of the intermediary, i.e. the final price). Say it without laying out, just for a throwback. If you know tao far and wide, I think you will have no difficulty answering this question.
+
avatar
+1
The 2.1S version fee with a 1.3 display in store on Tao costs 110 yuan, which equates to $15.97
how many intermediaries do not take, buy SAM, I drive to Ukraine forwarder (carrier), not to be confused with the intermediary.
+
avatar
  • oleg_s
  • 12 марта 2017, 15:39
0
$15.97, even $10 for import/overhead. Total $26, versus $30-35 on Ali. And if you use a coupon for Ali $15/20, the controller will cost the same $15, but without the gym. Is it worth the sheepskin dressing?

Please excuse me, I was not sincere, of course, I knew how much it would cost to buy a tao, but I wanted you to answer how much I would save by buying one controller.

In 2009, I had a valcoder jammed in my transceiver, I found it only on tao for about $2-3. While dealing with this tao, how to pay, how to carry - spent a lot of time. But I found out that the valcoder would cost me $90 with tao. Do you think I started buying? No, I bought it in Moscow, 120km from my house, for $100, a half-tank of gasoline, half a day of time. But I was very sorry for the time spent studying tao. And after almost eight years I again needed to buy something and the paths lead to tao. It makes sense to go to tao when you buy a lot and often, and when from time to time that Ali, in isolated cases and at all in the store around the corner. The goal does not always justify the means.
+
avatar
+1
this is your opinion, I'm more comfortable once a month to skimp on Tao, to bring yourself and friends all that is required ...
ASUP bought the controller 2.1S q front panel as in my review, only silver (not painted) - liner in the handle 900 series (links are in my review) - taking into account the weight of 0.25kg, the cost of delivery with overhead costs cost $2.5
$10 per import/overhead

it's if 1kg lead
And if you use a coupon for Ali $15/20
You can often afford such coupons subject to purchase from $30???
+
avatar
  • asup
  • 12 марта 2017, 16:55
+1
The words of Sancho 1971 fully confirm.
+
avatar
0
I have ALL soldering station weighs 0.497kg
+
avatar
  • oleg_s
  • 12 марта 2017, 17:11
-1
Can you please tell me version 2.0 with a 1.3 display better than version 2.1S with a 1.3 display? I just do not understand the point - the seller is one, and the price ver. 2.0 at $3 more expensive than ver. 2.1S. Do you have any assumptions/conclusions about this?
+
avatar
+2
first there was version 1.0, then 2.0, then 2.0S, then 2.1S
I just don't understand the point - the salesman is the only one
it's not a salesman, it's a JACK. When only these controllers started to appear on Ali, prices were quite affordable, and now the prices have inflated the PPC.
Man...
In the review everything kind of told...
in versions of the second series, if you use only soldering iron, there are almost no differences.
2.0 S and 2.1S added pump control for dismantling soldering iron.
+
avatar
  • oleg_s
  • 12 марта 2017, 19:02
0
In the review everything kind of told
I'm sorry, I just read all the reviews of soldering stations and porridge in my head. I don't remember where I am.

it's not a seller, it's a JACK
now the prices are inflated by the PPC
It's not a fact that the seller got it, maybe the supplier. They have one supplier. These controllers are sold from just a few vendors. In China, you can fake everything except your own. And this controller seems to be Chinese.
+
avatar
0
Controllers for soldering iron, hairdryer, combo soldering iron fen developed the same Chinese, all true.
It's not a fact that the seller was kicking, maybe the supplier
Then explain to me why Tao is twice cheaper?
Both Ali and Tao are all CHINA.
+
avatar
  • oleg_s
  • 12 марта 2017, 20:13
0
For example, we do not know what fees the sellers pay on tao and ali. It can be assumed that for the localization of ali, the possibility of accepting international payments, etc. for ali fees will be more. The tao is traded more than large suppliers of goods, rather than second-hand purchases. All the second-hand buys are sitting on ali. And of course, I do not deny it, on whether prices are bullied because the alternative is only in Chinese and sellers on ali use it.
+
avatar
0
So you've made the right conclusion
All the second-hand buys are sitting on ali. And of course, I do not deny it, on whether prices are bullied because the alternative is only in Chinese and sellers on ali use it.
We need to master Tao ;)
I believe me, there is nothing difficult, you just want to...
+
avatar
  • oleg_s
  • 12 марта 2017, 20:33
0
It is necessary to master if you constantly buy something on tao, and for the sake of several purchases a year - why? I'm now buying on Ali just because I can use coupons. All! I believe that in China you can buy only bolts and nuts. Nothing is more expensive than $10. If you buy then only a Chinese brand, and it is expensive. For the most part, I buy in the United States.

So far, the Chinese have learned to make only beautiful cases and beautiful packaging. Everything else needs to be finished, finished. And the insides of the same electronics burn after a month - six months. That's recently bought on ali heels atmel-s, so write them turned out 2-5 times and all, dump. I've paid extra for the purchase, so it's not a shame.
+
avatar
  • asup
  • 12 марта 2017, 07:54
+2
On the first and second link of the controllers' board of the last revision v2.1s and that fee that for $25 is the fee of the old version 1.00. How they differ I do not tell you exactly as he only recently received his fee with Tao (thanks Sancho 1971 !). Know for sure that the latest version of the board has additional contacts under the automatic tin pump and a little different kind of screen graphics.
+
avatar
  • oleg_s
  • 12 марта 2017, 08:36
0
Thank you!
+
avatar
0
graphics differ on the controller version from WOKA,on their board hardware implemented support for solders 900 series, T12 and JBC. That's just software support only for T12
+
avatar
  • ituner
  • 15 марта 2017, 00:39
0
On occasion recently ordered a clone controller based on the STM32 V2.1S board immediately with a display of 1.3 inches

arrived today
V2.10 firmware

the only thing that did not like this shift of the display in the window, probably sold out and glue the display to the panel below, and can replace the white (there is just the same) instead of blue, but I do not know whether to ressash

ordered separately aluminum panel with glass sent without the logo :)
+
avatar
  • kazlift
  • 31 марта 2017, 21:06
0
Can't you tell me how you can unstuck it? I'm going to have a shift, too.
+
avatar
0
Good day!
Tell me, please, where to find a scheme for the harvester board? Waited for her for more than two months, finally flew.
+
avatar
+2
Well, I guess that's where I ordered it.
Or here.

+
avatar
0
Thank you so much!
Where you ordered, there is nothing (ali). With the first picture everything is clear, on the second, because of the resolution, it is not clear what the elements and denomination. Beige rectangles is what? Bottom is 220/24? And the top one?
+
avatar
0
Doesn't anyone know?
+
avatar
+3
this kit was not collected by anyone, bought ready-made
+
avatar
+3
what exactly is interested, I can help on the connection, still disassembled, and in general this combaine cut me specifically, the soldering iron is covered, but the hairdryer works, because of this now it is impossible to use it in full force so to speak
+
avatar
0
Interested in what is the part on the wires between the two boards.
+
avatar
+2
Can you show more concrete on the diagram?
there's still a folk bp to work the soldering iron, this combo works with two bps,
+
avatar
0
+
avatar
+1
Look at it.
+
avatar
+1
Welcome! The highlighted fragment is a power supply for the Vacuum Pump. If you use a vacuum pump at 24 volts 10W then this power supply is not put. That's about it. , .
+
avatar
+1
Thank you so much for the information!
+
avatar
+3
and in general, this team cut me specifically, soldering iron
It's okay to fix/modernize;-)
+
avatar
+2
I have no doubt))
+
avatar
0
Do I take it there? If there are owners, could you see?
+
avatar
+2
There's no wires in the set?
+
avatar
0
There's a train and a few connectors
+
avatar
+1
That's nice
+
avatar
  • Forkoss
  • 18 апреля 2017, 23:52
0
Thanks for the review!
Is the firmware procedure for pure stained logging different?
+
avatar
+3
Nothing
+
avatar
  • Forkoss
  • 19 апреля 2017, 11:14
+1
Thank you!
+
avatar
  • Sascha
  • 22 апреля 2017, 13:30
0
@TheUasia:

The «red marked circle» is a DC-DC converter for the motor of Vacuum pump. There are vacuum pumps with 12VDC or 24VDC. For connecting a vacuum pump with 24VDC does not need this converter.
+
avatar
  • Sascha
  • 22 апреля 2017, 14:18
0
Does anyone know what type sensor (vacuum / pressure) is built (I guess is a vacuum) and from which manufacturer?

Will it be retrofitted on newer PCB (also new FW) all this work (see display)?
I think this will not work but still I ask question ;-)
+
avatar
  • djfixx
  • 24 апреля 2017, 19:36
0
Hello world. Does anyone happen to have firmware for such a fee? Accidentally nailed his re-stitching, and the backup campaign did not completely merged. I understand that the fee is, but maybe someone has one. I bought it myself by mistake.
+
avatar
+1
There's a different scheme and firmware is simpler...
+
avatar
  • djfixx
  • 24 апреля 2017, 20:22
0
I'm aware of the problem.
+
avatar
+1
you should look not here, but on forums in China
for example, www.yleee.com.cn/, www.shoudian.org or similar
may be lucky, though unlikely, Chinese greedy, like it's their intellectual property
+
avatar
+1
regvis on the www.yleee.com.cn/ website - nothing complicated
click on the search bar to beat the T12 STM32 (or other options) and see what will offer the search, look for your fee, and then try to ask questions on the firmware

or create your theme, show the photo boards and ask where to get the firmware
+
avatar
+2
Accidentally nailed his re-stitching, and the backup campaign did not completely merged.
Because of this haste "nailed" the fee, you would at least ask before sewing...
In STMka there is protection from reading and what you considered it "abra-kadabra" but not as a firmware.
Now this controller is "full", or you'll be very lucky... although it is unlikely :(
+
avatar
  • djfixx
  • 25 апреля 2017, 08:01
0
Well negative experience is also an experience, of course it is better to learn from your mistakes. It was in this controller that there was no read protection, apparently there were incorrect connectent settings or something else went wrong
+
avatar
+3
It was in this controller that there was no read protection, apparently there were incorrect connectent settings or something else went wrong
Naive ;)... Well, think logically, the Chinese are not fools, just so firmware open to leave open? What would be like this, the dude took a slink and merged the firmware from the commercial controller ... I sympathize with you and hope for a positive search for "free" firmware.
AS As written above sancho1971 you need to climb on the forums, well, or ask for help from Denis (aka salamatin)... Maybe he'll find something.
Comment is hidden

Comment is hidden

+
avatar
  • adjuster
  • 09 декабря 2017, 15:11
0
without STlinc it is possible to check something? (Available there are arduinki and usbAsp)
+
avatar
+2
ST_linc is worth a penny, a couple of bucks, it is not difficult to buy even an offlight, at the local barge ...
+
avatar
  • adjuster
  • 11 декабря 2017, 14:27
+1
I envy the white envy of people from big cities. In Siberia, a bear in the yard is almost the norm, and a barge from the radio bazaar is a rarity.
+
avatar
+1
so you have China near, shipping with Tao should be not expensive
+
avatar
  • adjuster
  • 11 декабря 2017, 15:28
0
But the debts are more
Joking around the internet shops in the nearest (170km) there is a ST_linc of 300p q delivery to the post office or transport company - the transport company will take another penny.
+
avatar
  • oleg_s
  • 11 декабря 2017, 08:13
+2
Are you sure your knob connection handles are correct?
+
avatar
+2
And the truth is the sensor and the t12 are confused...
+
avatar
  • adjuster
  • 11 декабря 2017, 14:36
0
Why? In one of the reviews laid out the scheme there on the board of the controller the sting case and "-" power are connected together, what difference does it make where they connect in a pen or on a board? You can also resister on 1MM on "-" static.
+
avatar
  • oleg_s
  • 11 декабря 2017, 14:52
+2
What does it have to do with it? "T12" and "mercury switch" to swap places
+
avatar
  • adjuster
  • 11 декабря 2017, 15:22
+1
I've got this photo so you don't get any more confusion. Thank you for your help.
+
avatar
  • adjuster
  • 11 декабря 2017, 14:30
0
No, I'm not sure, I have a stinger seller for something separately sent and they just flew out of China. They'll come and check. Painted specifically to learn from the seller the scheme of connection.
+
avatar
+1
he's a salesman - just a bargaining chip
he doesn't care about all these nuances, sold and nice, and you bought it once, then sort it out. Have you seen what your eyes were buying?
+
avatar
  • adjuster
  • 11 декабря 2017, 15:13
0
I work in the mine, I need a soldering iron for a slave in a car from 24In gas is not everywhere convenient to climb, in the nuances to understand was not, saw the Russian language in the menu q 24B and ordered. Well, sped, well, it happens, the toad gloats - so you need to reason soothes that we and one sting can without high technology
+
avatar
+2
Here's a look at your photo and photo djfixx
He's got a real photo, and you're from the store?
I think you've got a photo mirrored.
Like the boards are the same, and the location of the elements is different.
Make your own and on the purchase, only the fee.
+
avatar
  • oleg_s
  • 11 декабря 2017, 10:14
+1
I think you've got a photo of you.
And what is not seen on the sticker on the squeaker or inscriptions on the board? :)
+
avatar
+1
That's what I'm talking about;-)
+
avatar
  • adjuster
  • 11 декабря 2017, 14:51
0
No this photo is real. You tell me what you're interested in, I'll take a picture separately.



The controller came with an uns sealed display, the connector itself added, in the set it was not.
The seller to choose from offered a 0.96" and 1.3" display.
+
avatar
  • adjuster
  • 11 декабря 2017, 15:06
0



+
avatar
+2
and that's
Mirrored
+
avatar
  • adjuster
  • 11 декабря 2017, 15:14
0
Yes for the question to the seller - they say so or not to connect. As long as I'm silent, I'm waiting for an answer.
+
avatar
  • adjuster
  • 11 декабря 2017, 15:17
0
Included to the controller and to the handle were thermals and pen position sensors and two connectors one 5 pin the second 4s contact, wire five residential.
+
avatar
  • now6
  • 01 марта 2018, 00:35
+2
There was an alternative firmware for this board, he bought such by inattention
+
avatar
  • limoncn
  • 12 марта 2018, 00:12
0
cool, you can now collect yourself on a blue pill ))) (on a blue handkerchief)
+
avatar
+1
Please tell me, at the moment the solder is collected on the basis of the STC controller. I plan to take on STM. Which version is relevant at the moment and who on tao is better to take a ready-made controller with a display? M.B. this one? https://world.taobao.com/item/529249246589.htm

P.S. Block stands folk, the body is not grounded. The solder sent a couple of chips into the world. What is the best way to solve the problem?
+
avatar
+2
It is this link and is worth taking, there is on with displays on 1.3" blue and white, I buy there.
BP folk will suit, only remake it according to the methodology from Kirich (there on the muske more than once considered).
+
avatar
0
Thank you
But I have the right conder. The land and the "-" in the controller are closed.
+
avatar
  • firebie
  • 02 марта 2018, 22:14
0
Is it necessary to connect the green wire from the handle (sting) with the ground of the power connector (the 3rd contact of the network fork)?
+
avatar
-1
Do you have a grounding socket in your house?

I'm not connected...
+
avatar
  • firebie
  • 02 марта 2018, 22:54
0
I think there is. Cyprus, british standard outlets.
+
avatar
+6
Since the topic is about upgrade...
User Vladimir (vpuchkov) approached me with the problem that the encoder in the opposite direction works (twist to the right, and the menu up runs). In order not to cut the fee and not to buy a new encoder changed in firmware under another direction. At the moment for the 2.00 version and 1.3 display. Suddenly, whoever has the same problem.
Also thanks to the user TransMatrix merged from his combo station firmware. On the layout ($2 handkerchief) checked and activated. Suddenly who will burn down their station...
+
avatar
+2
Thank you Denis, I think a lot of people will come in handy.
The molot38x comrad just broke its...
But we have already done a little differently...
Wait for review
+
avatar
  • bestya
  • 18 мая 2017, 20:16
+3
I would like to express my gratitude to Denis aka salamatin for the elegant solution to the problem of the "reverse" encoder and modification of the firmware.
+
avatar
0
and I got 2.1S too with a reverse encoder, twisting the left running down... budget not to fix?
+
avatar
+1
Left is it like?
in the normal version, clockwise rotation increases values, against - reduces
+
avatar
0
I was already confused, but when I ran on the menu I was freezing out of the inversion... twist the clock (right) and the menu runs up. As Denis described.
+
avatar
+2
Made for 2.1S mod with encoder.
+
avatar
0
it is possible to attach a 2-inch screen to the station, as there is a www.youtube.com/watch?v=Q7E_XwIrYYo ?
+
avatar
0
perhaps, but you need to pick firmware, change the display driver, and given the language of the interface, you can see that the author of the video is Chinese and he, at least, has access to the source
+
avatar
0
Good Day Denis!.. My name is Dmitri. Dimoneset.
On the forum I read that you managed to merge the firmware from Combo-2v1 T12 on STM32.
Could you give me this firmware.
Thank you for your attention, Thank you in advance!!!
+
avatar
0
in this review there is a link to firmware.
+
avatar
0
There's no 2v1
+
avatar
+1
there are still such firmware
+
avatar
0
Is it with q?
2.0, 2.0S, 2.1S there is also
+
avatar
  • 8AleX8
  • 26 мая 2017, 06:23
-1
Tell me what the problem can be, with the power supply goes 24 volts, and on the scoreboard 50-60 volts and the temperature with the question, very much warms the sting, if a little from the minimum rewind, it turns red. T12 controller v 2.2
+
avatar
0
why produce the same messages in different toppings?
You have a completely different PS controller on the STC controller
+
avatar
  • 8AleX8
  • 26 мая 2017, 10:09
-1
Obviously, different stomps, isn't it?
+
avatar
0
tops are completely about another controller
Don't you?
+
avatar
  • 8AleX8
  • 26 мая 2017, 11:23
0
Maybe there are those who are in the subject.
+
avatar
+1
Maybe someone will come in handy, that's the kind of weirdness I found.
The 2.1s version board with the blue 1.3 display.
I had to stitch and on firmware 1.3 native display 1.3 did not work at all, earned only on 0.96 firmware.
The separately purchased white display 1.3 earned on firmware 1.3 completely, on firmware 0.96 was a strip on the right.
Externally, the displays are the same size, only the boards are different.
Firmware from this topic.

In addition, such problems came out.
During the rotation, the encoder began to blink the display and dumped on the main screen. Not constantly but periodically and at some point completely extinguished. At the same time, some sounds were heard when the encoder rotated.
Sin on the display, ordered, on arrival began to understand and found a red-hot stabilizer and half-living processor.
As a result, we had to change the processor and stabilizer.

Now I've written salamatin, we need activation.
+
avatar
+3
A little refinement of the 907 pen.
Extended the insert, drilled a hole under the carving and that's what happened.


+
avatar
+2
On the radiocot found a similar self-made liner
For straight hands
+
avatar
+1
in the mail regularly.
There is nothing interesting except the Russian language. Bases sting are absent, what calibration is not known, such is the impression that the people's STC'LED transferred to STM32-OLED
+
avatar
  • Gromily4
  • 29 августа 2017, 09:09
+1
So it's better to buy versions 2.1, 2.1S?
+
avatar
+1
Uniquely
this "new and fancy v3.5" has nothing to do with Developer 2.0, 2.0S, 2.1S
v3.5 some separate, non-dependent development
+
avatar
+1
Information about this controller regularly comes to the mail from the Chinese store (soon probably the recipient of spam will send), but the real application of this controller I have not found ...
+
avatar
  • KruzoS
  • 15 сентября 2017, 17:42
+1
Good time of day! Gathered a station on the controller STM32, version of the board 2.00. Changed the display to 1.3, did everything on the recommendations, everything turned out the first time, a special thank you to Denis aka salamatin, for help and assistance in re-processing. There was only one problem: the soldering iron does not come out of hibernation, if you do not press the encoder. That is, there is no reaction to the motion sensor (from the waiting mode - all right: took the soldering iron from the stand - went heated). Has anyone ever encountered such a problem? The motion sensor is mercurial.
+
avatar
+2
Try changing settings in menu 01. Standby - Mode: Auto (automatic), Shake (vibration), Switch (switch), Manual (manual)
+
avatar
  • KruzoS
  • 15 сентября 2017, 21:03
+1


Tried in different modes, the effect is one: as soon as entered the dormant - only the encoder is displayed in the working. Another interesting point has surfaced: after the appearance of the screensaver (screen keeper), on standby - soldering iron quickly goes into working mode, but the screensaver is not removed, only encoder. It does not interfere with the work, but you need to try to disable the screensaver. I'm going to experiment and I'm going to write it off.
+
avatar
+2
I don't remember exactly, but it's kind of normal behavior and I had the same.
I can check in 4 hours (if I still need to).
+
avatar
0
I just don't remember...
I have a station does not go to sleep (does not have time). It either works and the maximum is on standby, or it's off.
+
avatar
+2
If you fell asleep - the temperature on the display dropped to the room, then awakening at the press of the encoder. If the expectation is I have a temperature of 150 degrees - then the movement of the vibration sensor. Controller 2.1s
+
avatar
+1
Thank you Dima...
That's the way it is.
+
avatar
  • KruzoS
  • 15 сентября 2017, 21:14
+1
It's possible. But the screensaver was definitely gone. Man... just now I noticed that I have a "reverse" encoder. I guess we're going to have to re-forgive again.
+
avatar
+1
I guess we're going to have to re-forgive again.
firmware is laid out on Yandex, link in the review text
T12_v.2.00_OLED1.3_enc_mod.hex
+
avatar
  • KruzoS
  • 15 сентября 2017, 21:37
+1
Thank you! I'm already collecting back, the firmware went well. Now we have to reconfigure everything first.

I didn't have to: all the settings are preserved! :)
+
avatar
  • KruzoS
  • 15 сентября 2017, 21:45
+1
Apparently, not expecting the temperature to drop to room, it is enough station just to go to sleep, even having a waiting temperature of 150 degrees. At least that's what I have.
+
avatar
+2
Don't forget to reset after the firmware, for proper initialization... otherwise glitches are possible.
On the occasion of awakening: there are two modes... sleep: falling asleep at a set temperature (100grd.) heating will be from the set temperature, the solder wakes up on the sensor, and shutdown: shutdown, the indicator shows room temperature, the soldering will turn on at the click of the encoder button, heating will be from room temperature.
+
avatar
  • h0per
  • 17 сентября 2018, 15:52
0
Another Nuance caught:
www.youtube.com/watch?v=egOZKFNGCYM

At a high of 480 C getting ERROR
At the same time, the load jumps 0 - 100
Sting T12-BL, HW 2.1s, SW 2.10

Has anyone ever done that? Is the controller crashing or stinging?
+
avatar
0
KSGER sting?
Did you check with another sting?
+
avatar
  • h0per
  • 18 сентября 2018, 13:09
0
The kit is entirely KSGER. There are no other regrets. There's nothing to check. You'll have to wait for the other stings to come. They're coming next. The seller says it's all about regret.
+
avatar
0
remove the white cap on the sting and check the contacts, preferably to drink them, how to do look in the net ...
+
avatar
+1
may also be in regret the contact is cut off.
although I had it when I didn't put out the temperature of the cold sleeping properly.
+
avatar
  • XProg
  • 08 октября 2017, 17:06
0


please help.
+
avatar
+1
What kind of controller is it???
It's like a soldering iron bottle...
+
avatar
  • XProg
  • 09 октября 2017, 08:26
0


V2.01
1.3'
+
avatar
  • XProg
  • 09 октября 2017, 08:56
0


STM32F101CBT6
+
avatar
+2
Kaygen is only in Denis, aka salamatin.
knock him in the face, help
+
avatar
  • XProg
  • 09 октября 2017, 11:06
0
I can help you reach salamatine.
I need a keygen.
+
avatar
+1
I don't have a keigen.
Kaygen has only Denis, aka salamatin.
+
avatar
  • XProg
  • 09 октября 2017, 08:34
0
2.1S upgrade dont work.

STM32F101CBT6
+
avatar
+2
So firmware for 2.1S and won't become on this board, the crucifying controller is different
+
avatar
  • XProg
  • 09 октября 2017, 10:05
0
How can I make it work? I don't have your back.
What is RG1 and RG2?

I didn't back up.
+
avatar
+2
Did you change the display and re-ask the controller?
A backup won't help...
What is RG1 and RG2?
in the review I wrote about it, it's the response codes to ID1 and ID2.
+
avatar
  • XProg
  • 09 октября 2017, 11:00
0
I haven't changed.
+
avatar
  • Ggg
  • 18 октября 2017, 14:03
+1
aliexpress.com/store/product/Ksger-T12-STM32-OLED-DIY/1486111_32836043839.html
How is the price/quality? Can I get it? Taobao self-assembly is not an option, the plastic case is not a hindrance.
4 themes read, in the stones tangled...)
+
avatar
+2
2.0 version with 1.3" display - want to take
+
avatar
  • Ggg
  • 18 октября 2017, 17:16
+1
Thank you, then I'll take it.
On displays more or less clear, and according to versions: what is the last at the moment? Here 2.01 write, somewhere 3.5 slipped ... Also understood that the firmware is different - 2.09, 2.1, or something much newer? Are the differences between these versions and firmware significant?
+
avatar
+2
the latest version of the 2.1S board, firmware newer than 2.11 no

3.5 is not from here at all, some left development has nothing to do with this, the only advantage is the Russian language, and so the is complete
+
avatar
  • Ggg
  • 18 октября 2017, 17:46
+1
Thank you, we've cleared up the situation.
Well, and ordered.)
+
avatar
  • Ggg
  • 09 ноября 2017, 20:15
0
Taeek... The encoder with the handle does not press to the end, but clicks as if pressed. For five minutes, I thought the percent was glitching. But that's fine.
Should the menu flash when navigating and changing items? Blinking, but not always, I don't see the dependency. Sometimes even the screen goes out for a fraction of a second then smoothly lights up.
By StandBy. How does "Auto" mode work?
"Shake" - is it not shaking if then it goes to the standbay?
So is the "manual" an encoder to send to the standbay?
HW - 2.00 SW-2.09 station came.
+
avatar
  • Ggg
  • 09 ноября 2017, 20:50
0
We've dealt with the stand-up.)
+
avatar
+2
Read the menu description here
mysku.ru/blog/taobao/45851.html

I had one.
HW — 2.00 SW-2.09
until I changed the screen

Sometimes even the screen goes out for a fraction of a second then smoothly lights up.
I don't have that.
+
avatar
  • Ggg
  • 09 ноября 2017, 21:26
0
That's how I read it. Still, not everything is clear:
Auto - rolls in S.bye h/h time time, (if there is no vibration? then at work too, what can in wait to leave?
Shake - if there is no vibration standbay (five hours/time timer?)
Switch - in general not understood (encoder to the left or what? why then trace the point.)
Manual is purely encoder switching, right?
As that is not explicit and inter-breaking points are obtained ...
With the rest of it seems to have sorted out - blinking while maintaining the settings - the feature is such, so understood.
Well, the handle of the encoder pancake a lot prevented to understand in the beginning.)
The stand-and-greet is a very important function for me, contributed a lot to the decision to buy.
+
avatar
+2
wrote already below

Menu:
01. Standby - Waiting Mode settings.
This item displays:
Mode - Stand-off mode: Auto (automatic), Shake (vibration), Switch (switch), Manual (manual).

Put
Shake - vibrations of the ball or mercury in the sensor
Or
Switch is a one-time sensor switch from one position to another
+
avatar
+2
Read the menu description here
+
avatar
  • GarikXP
  • 08 ноября 2017, 01:26
0
Sos! Help the plc with the SCHEME of connecting the PEN of the FX-9501 solder to the solder on STM32 2.1S. Wire 5 residential. With the handle came a package with a set - a ermistor, a mercury sensor, a position sensor sw200d, a conder and some other decal. I can't figure out what it takes to handle this set. There's different information everywhere. Thank you for your help!
+
avatar
+1
Read this topic mysku.ru/blog/taobao/45851.html#comment2010489.
Here's a picture from the theme:
+
avatar
  • GarikXP
  • 08 ноября 2017, 14:33
+1
This picture from the seller's website on Ali aliexpress.com/item/Ksger-DIY-T12-FX9501-STM32-OLED/32837360306.html In English The fact is that the kit that this seller sells, there is only a SW200D sensor, and the picture shows a mercury sensor. That's what baffled me. Some add a capacitor from the kit between plus and minus.
+
avatar
+1
The sensor suits anyone, the main thing is that the contacts would switch.
Switch modes are set up in the controller (read review)


I don't have a capacitor and everything works
+
avatar
+1
All as Dima suggested, the main thing is not to confuse red and black, the polarity of the hook connection is important for the built-in thermopar
+
avatar
  • GarikXP
  • 08 ноября 2017, 14:40
0
Is it the right connection? The SW200D sensor is connected by a plastic glass up. Or is it better to use a mercury sensor in a glass flask?
+
avatar
+1
The sensor can be used any- the work they perform the same, only the mercurial silent and SW200D torts the ball :).
+
avatar
+1
how to put a ball sensor look the comment above

Although it is not fundamental for this station
Menu:
01. Standby - Waiting Mode settings.
This item displays:
Mode - Stand-off mode: Auto (automatic), Shake (vibration), Switch (switch), Manual (manual).

You bet Shake (vibration) or Switch and should work normally
+
avatar
  • adjuster
  • 08 декабря 2017, 22:53
-1
Excuse me please for maybe a stupid question, but why do you need an NTC termistor in a pen?
+
avatar
+1
read carefully reviews and comments on them, as well as first understand how the thermopara works
+
avatar
  • Kembrik
  • 09 января 2018, 19:36
+3
Got into the Chinese group, where the creator of this controller lives. They have firmware on the file exchange dated May 14, 2017. Those in this topic on Yandex, laid out by the Chinese on May 15, 2016. Now the hands itch to fill the firmware fresher (good activation codes are already there, for which thanks to Denis). Or maybe someone has already installed them? Is it worth it, has changed what or not?
Probably we should wait for information on alternative firmware, and there we will experiment.
+
avatar
+3
Stitch, then write what was improved there ...
Reference to Chinese group welcomes...
+
avatar
  • Kembrik
  • 09 января 2018, 20:12
+4
The group they have in the messenger is the equivalent of IC (if anyone else remembers). The group number is: 302429021. The group is closed and accepted there by the approval of the administrator. The file-sharing goes only through the messenger itself, I could not get a direct link. Here's the link: qun.qzone.qq.com/group#!/302429021/home
I didn't find any descriptions of the new firmware. It seems that 2.11 works normally, which is not clear there to improve.
By the way, how are the stings? Just the other day, the BC3 died, closed on the hull. Inside something dangles, but the soldering iron never fell or hit, soldering neatly and not much. More than 350 degrees and never heated. The sting from KSGER aliexpress.
+
avatar
+3
Nine grand. Three in active work. None of the nine has refused yet...
+
avatar
  • Kembrik
  • 09 января 2018, 20:44
+3
So I'm lucky. :)
+
avatar
+3
better yet, pour the firmware and put it on the exchange file.
+
avatar
  • Kembrik
  • 09 января 2018, 20:46
+3
yadi.sk/d/5geCwoxt3RJfJk
If you didn't make a mistake in matching the displays:
SSD1306 — 0.96
SH1106 — 1.3
If anyone is brave, then say no. It's interesting to know what it is.
+
avatar
+3
Transfer files to Google drive
Yandex in Ukraine (officially) is not available
+
avatar
+4
volume of firmware by 1KB more, and what is the difference is not clear
+
avatar
  • Mvf
  • 13 марта 2018, 09:42
0
I sewed HW 2.1S. Display 1.3." SW was 2.10, became 2.12. The activation code came from an online activator. At first Sewn T12_v.2.1S_OLED1.3.hex and others from there, the display was without an image and the firmware, like, did not work (at all). He sewed T12_HW21S_Encryption-SSD1306.hex - earned. The difference on the board is the STM32F103 processor instead of the STM32F101.
+
avatar
  • Mvf
  • 13 марта 2018, 10:17
0
Disheel fee ver1.3
+
avatar
  • firebie
  • 13 марта 2018, 12:14
+1
It has already been written that if 1.3" - you need SH1106, and if 0.96," then SSD1306.
+
avatar
  • Mvf
  • 13 марта 2018, 16:43
0
The firmwares from the previous source, like Denis, didn't work. There were also for 1.3 and 0.96 displays. And with the "reverse" encoder. Those firmware worked on my board with STM32F101 with a display board ver. 1.1 (1.1 - from memory, now I can not open). Let me be clear, 2.1s and 1.3."
+
avatar
+1
The man display 1.3" and the firmware came up with the driver SSD1306.
+
avatar
0
So I read and I can't understand HOW?
When I soldered the display, then from the right were 2 vertical strips (photo at the beginning of the review)
that's why the controller decided to re-stitch
Match:
1.3" firmware T12_HW21S_Encryption-SH1106.hex
0.96" firmware T12_HW21S_Encryption-SSD1306.hex
+
avatar
  • Mvf
  • 13 марта 2018, 22:49
0
Kembrik wrote: "If not wrong..." I, in fact, was in a hurry and did not pay attention to the resulting correspondence, saw in the archive with firmware familiar beeches 21S and 13 and sewed. Work. Without even thinking that SSD1306 is a controller. I gave my processor and version of the display board. Now even measured his display roulette (through the glass on the image) - 33mm diagonally there. In the archive with firmware it would be good to "recognize" the Chinese text in the picture and translate for confidence.
Looked at Ali - there are many of these: "1.3 inches blue OLED module ssd1106 Drive IC compatible with ssd1306 IC 128/64 IIC/SPI interface".
+
avatar
0
mvf March 13, 2018, 22:49
Kembrik wrote: "If not wrong..."
I'm not mistaken:
1.3" firmware T12_HW21S_Encryption-SH1106.hex
0.96" firmware T12_HW21S_Encryption-SSD1306.hex
I have ALL firmware for THESE controllers (2.0, 2.0S, 2.1S) for displays 0.96 and 1.3, including modified denis, aka salamatin, with inverse encoder rotation.
Versions 15 May 2016 (2.11) and May 14, 2017 (2.12), lie here
+
avatar
  • Mvf
  • 14 марта 2018, 08:59
0
There is a firmware SMD_Rework_v.1.1_SH1106_OLED1.3.hex. Kind of like SH1106, but OLED1.3. Here,for example.
+
avatar
  • Mvf
  • 14 марта 2018, 09:51
+2
One more thing. I wasn't too lazy to recognize and translate the notes into Description.jpg. It turned out like this:
1. See A version of the equipment? PCB marking (?)
The 0.96-inch screen is the SSD1306 driver. Both types of drives have 1.3-inch drives available.
3. When it is not possible to identify the screen driver, you can first write down the firmware SSD1306.
If a bright line appears on the right when it burns, the screen is controlled by SH1106. Rewrite the firmware SH1106.
Correctness is not guaranteed. (I added it from myself)
+
avatar
  • Kembrik
  • 14 марта 2018, 13:48
+1
Maybe it'll be easier to translate.
1、硬件版本请看PCB上的标注。

2、一般0.96寸的屏均为SSD1306的驱动。1.3寸的则两种驱动都有,具体请自行与屏商家确认。

3、在无法确定屏驱动时,可以先写入SSD1306的固件,如点亮后发现右边出现一条亮线,就说明屏是SH1106的驱动。再重写SH1106驱动的固件即可。
+
avatar
  • Mvf
  • 14 марта 2018, 19:05
0
Recognized correctly. But when translated, the meaning can change dramatically when the gaps are set.
It turned out (not quite verbatim, for readability) so:
1. Hardware version of the s. marking on the circuit board.
2. The 0.96-inch display is usually controlled by the SSD1306 controller. For 1.3-inch models, there are two types of controllers (SSD1306 and SH1106?
Please contact your own screen provider (for clarification).
3. When the display controller cannot be identified, the SSD1306 can be recorded first.
The appearance of a bright line on the right, when the display controller is on (of course), means that the screen is controlled by the SH1106 controller. Re-write the firmware on SH1106.
It's a good thing. Translator.
+
avatar
0
At first Sewn T12_v.2.1S_OLED1.3.hex and others from there, the display was without an image and the firmware, like, did not work (at all). He sewed T12_HW21S_Encryption-SSD1306.hex - earned.
you wrote yourself that you didn't have a picture, not a two-pixel band.
+
avatar
  • Mvf
  • 14 марта 2018, 21:27
0
I first swiped firmware from another source that worked at another station. And that in it (station) another, I also wrote.
+
avatar
  • Kembrik
  • 13 марта 2018, 12:32
0
Is the picture on the two-pixel display unsliding?
+
avatar
  • Mvf
  • 13 марта 2018, 16:57
0
Cut-off symbols and artifacts were found. The symbols on the right (% and C) seem to be located close to the right side of the screen. Under the dark glass does not interfere.
+
avatar
  • Kembrik
  • 09 января 2018, 20:54
+4
I don't think it's a big secret. There's more than 900 people in the group. Especially here we help the Chinese to popularize his brainchild, marketing is free, so to speak. He's even grateful to us. :)
+
avatar
+4
we're free to use his brainchild using a keygen from Denis
They have on the file exchange are firmware dated May 14, 2017
Somewhere in this period Denis was toured from this group
it is possible that in the new firmware the protection has been changed

Perhaps we should wait for information on alternative firmware...
+
avatar
  • Kembrik
  • 10 января 2018, 01:29
+4
we're free to use his brainchild using a keygen from Denis
Well, not quite for free, the money then the seller had to pay. Supported the Chinese economy.

Somewhere in this period Denis was toured from this group
So I should expect the same. :)
The number of people in the group periodically decreases. Perhaps remove those who are not active. I'm not strong in Chinese, so I look at pictures.
+
avatar
+3
We don't help the author ;) and greedy store KSGER,which at the expense of our articles promoted their store, as well as sit here and our "knocks" who merge and help the store ;)
Oh, I'm afraid that this shop will get to the new firmware... yes would be entitled to be first in profit!
I wonder who's in defense of the magaz... will say something))))
+
avatar
+3
I wonder who in defense of magaz... will say something))))
Aha
will be killed
+
avatar
  • Kembrik
  • 10 января 2018, 20:52
+4
yes, in defense, they're going to give me a return on the controller's power supply, they're not going to report it. :)
As for the firmware, I doubt they're stitching. I got the controller version 2.10, and I ordered it a month ago. In theory, the firmware 2.11 was already available for a long time.
+
avatar
+1
As for the firmware, Sasha wrote to me that they are negotiating with him, like they want to buy it out.
+
avatar
+3
and it's going to end there...
will be KSGER exclusive seller of controllers with alternative firmware
and They will put a strict condition to Sasha: not to sell anything on the side

so I doubt we're going to see an alternative firmware here.
it is possible that the delay in publication is related to this
+
avatar
+3
That's the turn :(. And I'm already paying a blutus with Ali pull ...
+
avatar
+3
While we do not panic, the author should wait and he is silent ... maybe holidays.
+
avatar
  • Kembrik
  • 10 января 2018, 20:46
+3
I couldn't resist, curiosity got the better of laziness. I sewn a new firmware. Firmware version 2.12. I'll please everyone who has 2.11, when moving from it did not need activation.
From the changes: eight JBC stings were added to the base, and now there are 106 stings in the base.
I didn't notice any more updates.

+
avatar
  • Kembrik
  • 10 января 2018, 21:11
+4
Speaking of JBC stings, all on the same Chinese file exchange slipped such pictures:





Maybe someone's going to need it.
+
avatar
+2
Look, in working mode the temperature is displayed in whole digits or with tenths?, As in a double board (soldering iron hairdryer).
+
avatar
  • Kembrik
  • 10 января 2018, 21:45
+4
Whole, tenths will not fit, the clock interferes.
+
avatar
+3
Thank you, so on the dual board the watch is only displayed on the hairdryer screen...
+
avatar
+3
Just sewn, activation controller did not scare, so Denis was right, the code is stored not where in the old firmware 2.09
+
avatar
+3
Tell me, when the firmware-calibration and settings fly off?
+
avatar
  • Kembrik
  • 11 января 2018, 20:51
+2
The clock doesn't go down and the corrective factor too.
+
avatar
+3
About... KVI camrade will be glad) he likes the watch)))
+
avatar
  • Kvi
  • 12 января 2018, 14:29
+3
Come on)))), I just have this station fixed at work on a shelf above the desktop. The display is just opposite the eyes. You can see how much is left for the end of the working day))))).
The second day I introduce a coffee. Adjustments. By the method that was described. Let's see what happens.
+
avatar
+4
For the normal initialization of the new firmware... reset is better done.
+
avatar
+3
Then until I stitch-up the sting to calibrate the :)
+
avatar
  • Kvi
  • 11 января 2018, 14:02
+1
If the calibrations are stored in the outer 24s08, you can remove the copy and then refos after the firmware.
+
avatar
+4
This is an option, but it requires a separate ;)
+
avatar
+3
There are a programr - but so far there are no strong differences, so it does not burn. Don't touch :)
+
avatar
+4
100% agree.
And I'm just for the sake of experimenting ;)
+
avatar
+1
to the base of the sting added eight JBC stings (93-100)
99% buy Chinese sting, 1% original, I wonder how much - buy JBC. :)
+
avatar
  • Kembrik
  • 10 января 2018, 21:13
+4
And for fun, who's going to determine what the Frakinstein is?

+
avatar
+2
75 percent management of two stings from one encoder -- possibly tweezers
+
avatar
+2
The fee of 2.1s is another 2.1s but not all... I think maybe tweezers... But why another controller... there's enough more channel OU, for the second sting and power part (Mosfet, etc.)
+
avatar
  • Kembrik
  • 17 февраля 2018, 13:08
+3
So yes, it turned out to be tweezers.



+
avatar
0
Del.
+
avatar
+2
who has the opportunity to believe whether it will work on these boards, such an indicator.

1.54 inches 7pin white OLED Screen module ssd1309 Drive IC compatible for ssd1306 SPI Interface 128-64
link found in the review on utube.
smo.to/pC5Kc
+
avatar
+1
to do this, at least you need to have this display
+
avatar
+1
reassuring that the driver's chip is appropriate.
+
avatar
  • zalvis
  • 04 февраля 2018, 21:51
+1
All health.
I've already posted the news, but in a different topic. I decided to stay here, it's more correct.
Looks like a new firmware has come out.
Who heard what, saw?

aliexpress.com/item/Ksger-T12-STM32-OLED-V3-0-DIY-fx9501/32851333426.html

Firmware version 2.12,and where to download it?
I'd try to pour it, too.
+
avatar
0
in one of the themes on these solders laid out, a link to the Google cloud.
+
avatar
  • Kembrik
  • 04 февраля 2018, 22:12
0
A little higher on the comments climb. Links are on Yandex and Google.
+
avatar
+2
in this firmware 2.12 added support sting JBC, above already wrote about it
For T12 nothing new

About 3.0 - in my opinion this store rewrites the basic for itself
+
avatar
  • Kembrik
  • 04 февраля 2018, 23:00
+1
About 3.0 - in my opinion this store rewrites the basic for itself
The version of the wiring board is very similar to the original 2.0. Only add the battery and power.
Someone's go is left with a lot of boards of old versions, and they also need to sell. That's misleading. I watched the video at the seller, nothing new to see. Just mixed the menu items, and the main screen reshuffle done.
+
avatar
+2
if I'm not mistaken, the version of the board 2.01 with wiring under the connector GX12-5
I watched the video at the seller, nothing new to see.
The start is going a little faster, perhaps id check cut out
+
avatar
  • Kembrik
  • 04 февраля 2018, 23:39
+1
if I'm not mistaken, the version of the board 2.01 with wiring under the connector GX12-5
That's exactly what Ver2.0 is..
There is no version 2.01 in the original. There are Ver2.0S and Ver2.1S.
+
avatar
+2
You're a little wrong.
Ver2.0 - I have in the review and in the soldering station stands

and in the store just 2.01

Or here from the store
+
avatar
  • Kembrik
  • 05 февраля 2018, 06:44
+2
I'm telling you, I have screenshots of the developer's original boards. He posted them on a Chinese forum. Your V2.00 fee from the review is not his product. ;) The Chinese have already thoroughly confused everyone, both firmware and boards. :)
+
avatar
+2
maybe;-)
but photos from the Chinese forum/forums are not available to everyone, something that has been a bunch of clones I know, myself met different options with the same designation.
Most users are guided by photo boards from stores
+
avatar
0
Del
+
avatar
+3
The font is kind of gnarled...
+
avatar
  • zalvis
  • 04 февраля 2018, 22:29
0
Okay, well, it looks like I've already downloaded it turns out.
It's not a lot of stupid, sori.
+
avatar
+2
There is a desire to collect all articles and comments on soldering stations in one place
A little systematize a lot of information
Any idea how to do it better?
Offer options.
+
avatar
  • Kembrik
  • 04 февраля 2018, 23:34
+3
For such things used to use forums. :)
In the first message of the topic, the curator collected all the important information. And then there was the discussion.
If anything comes up, knock me in the face, help with pictures of the original boards.
In principle, there are pictures of clones. By the way, 2.01 is a hike and there is a adjusted clone of the ver2.0 version.
+
avatar
+3
That's the thing, that no one will do it here, and reviews are too much applauded ...
And the next bliss from the store that write a review - get a discount or a rollback - only breeds a bunch of stupid reviews from not much educated users, in the comments to which have to explain everything, once again, and some are indignant when they instead of an answer, are invited to independently study the material, understand and not produce stupid questions ...

Once again there is the idea of a separate blog or forum (maybe on a cat or soldering iron)
+
avatar
  • Kvi
  • 05 февраля 2018, 20:56
+3
Better article on a cat. Then we discussed it in the forum.
That's who's going to do it. There's a lot of work to do.
+
avatar
  • Kembrik
  • 05 февраля 2018, 22:24
+2
It seems to me that it is possible to organize a topic without an article. I'm for the cat, too.
+
avatar
  • Kvi
  • 05 февраля 2018, 23:12
+1
Just in the topic will be a lot of garbage (as here in the comments :)).
And in the article you can put on shelves: the design, features of various revisions, displays, how and what to sew, the differences of the firmware, the structure of the menu, calibration, power supplies, encoders ... That is all the things about which most of the same questions.
But the discussion is in a separate topic on the forum.
+
avatar
  • Kembrik
  • 05 февраля 2018, 23:25
+1
And then the article can be edited if necessary? I suspect not.
And in the topic all the information can be shoved into the first post, and then quietly edit it.
+
avatar
  • Kvi
  • 05 февраля 2018, 23:32
+1
Well, for this I will not say - I have not written an article on the cat yet :)
+
avatar
+1
Support
to make an article, to paint the features of boards, different BP (without going into the specifics of circuitry - as no like RADIO-KOT), firmware, pens, etc.
and in the discussion, in the first post to add new information

again in the discussion there will be a lot of garbage ;-)
+
avatar
  • vulkan35
  • 07 февраля 2018, 18:33
+1
in the discussion, in the first post to add new information
I'll support it, too. Here's not a bad forum with the possibility of further editing of the "cap." Probably there will also be an opening theme on the assembly and launch of the controller unisolder 5.1
+
avatar
0
attendance is much less than not a cat or soldering iron
+
avatar
+5
I begin to collect material on the article, who has what is interesting and who is ready to share the info can send to the soap: sancho-1971@i.ua
There is a great desire, but absolutely no time. Soon I do not promise, but to collect, generalize and organize it is necessary.
+
avatar
0
Please tell me whether it is worth buying PS on STM32 2.1S OLED 1.3 ($70) or is there something newer? Thank you in advance.
+
avatar
+2
At the moment the last fee is 2.1S FW 2.12, the screen of your choice is 0.96 or 1.3 with a great handy ;)
Don't be fooled by the new version v3.0 is a slag from the store!
+
avatar
  • mtkam
  • 16 февраля 2018, 21:55
0
Tell me, collected PS on STM32 2.1S 1.3 KSGER in the case, when you turn on that works normally, then asks to enter the activation code, what can be the reason ?
+
avatar
+1
Did you re-forgive it?
If YES, knock on the face of Denis, aka salamatin
+
avatar
  • mtkam
  • 16 февраля 2018, 23:30
0
No, the new one was assembled into the ali case, requested the activation code, after the power outage, worked, then a few more times, now only the activation code, the controller was drunk - did not help
+
avatar
+3
write to the seller let the code, do not give a partial refund, and contact the person who advised sancho1971
+
avatar
+2
There is no sense to shoot the controller, the activation code requires not a controller, but a program
knock on Denis's face
+
avatar
  • Kvi
  • 17 февраля 2018, 21:22
0
Answered in another topic. But again, check if the SDA,SCL (5.6 leg) signal comes from the memory chip to STM ki. Maybe there's a signal.
+
avatar
  • tofik71
  • 25 февраля 2018, 13:09
+2
Jbc support is interesting, but the question of what series? if you take less affordable
priced at the C245 series (on Ali with delivery within 1t) then the starting current y 245
within 6 amps, the fact that BP needs at least 6a is unequivocal, but it may have to
At JBC stations, heat-change, but also from
245 stand-ins don't work well.
+
avatar
  • vulkan35
  • 26 февраля 2018, 18:32
+2
on Ali with delivery within 1t
The Sting 2245 series has long been discontinued, all that the Chinese offer 95% copy, on the ali originals 2500-3000r.

2245 series:



Original C245 stinger with container:



Here is a quality copy of the sting T12-11, the Chinese are delighted and the price tag is normal.

Manufacturer's website.
+
avatar
  • tofik71
  • 26 февраля 2018, 21:33
0
Thanks for the information, but I didn't write that it was original.
Copy and not 95%, but 100% and they do not hide it.
the original can afford the units and whoever is on it
And so, someone takes a cheap pen T12 or 900 series and sculpts to
it has a controller that is three times more expensive than the handle itself, and
and someone takes a good pen like Wsp80, zuick203 or cartridges
Hakko t20,Jbc2245 let and withdrawn from production, makes pens,
analog controllers and works a good tool.
+
avatar
  • limoncn
  • 11 апреля 2018, 00:20
0
write back about my modernization
2.1S (LUT) fee... The 0.96 display runs on the firmware SSD1306 normally.
i2c bus displays
I replaced the display at 1.3 with Ali, but the trick failed, poured firmware from ssh1106 also did not help ...

Found in the online test firmware for SSD1306 and SSH1106 stitched... displays work, with SSH1106 running on firmware from SSD1306... It turns out the displays are working... But they don't want to work in the soldering iron. . . .
Here's a link to the lot

checked, displays (0.96 and 1.3) i2c addresses the same
+
avatar
+1
The link didn't pass.
+
avatar
+1
Can you try to transplant the module 1.3 on a handkerchief from 0.96, maybe a joint in the headscarf with Ali?
Or the firmware is not the same stitched, as I understood you have a fee 2.1S homemade (LUT)?
+
avatar
  • limoncn
  • 11 апреля 2018, 20:38
+1
all true handkerchief homemade, it inserted a blue board with stm32f103c8
Blue handkerchiefs (with stm32) and conductors are enough for the display test

firmware has already tried everything that is there
The Chinese asked for a diagram on the display 1.3
scheme here"cloud.mail.ru/public/47kM/9MCvQgmrL»

I look at the log analyzer that walks on the bus ...
The 0 x78 display address is true...
the only embarrassment is that the SDA signal starts at 2 pina instead of one... Weird...
+
avatar
+1
a few more circuits of ice displays
drive.google.com/drive/my-drive
+
avatar
  • limoncn
  • 11 апреля 2018, 22:58
+1
henri2002
Please correct the link, it is only valid for the owner of the drive...

I've been digging up some interesting things
exchange with EEPROM goes at 10kBod, and with oled at 500 kBod
+
avatar
+1
It seems to be written that for everyone.

Try this one.
drive.google.com/file/d/1SfSyZZ4Og-u-PsRZS_mmVMr2te12cZnh/view?usp=sharing
+
avatar
  • limoncn
  • 12 апреля 2018, 00:10
0
Now Running Your Link

Here's a photo of my display



who is sick... (not started with STM T 12)
I'll see what's going on on his tire tomorrow.
Log analyzer shows as if SCL floats at frequency...
+
avatar
  • limoncn
  • 12 апреля 2018, 10:38
+3
I beat him
Thank you Rigola... I looked at the oscillogram and everything became very clear
The problem is simple and banal came out...
on the i2c bus the data goes too fast and the height of pulses is small (less than 1B long pulse 2mkC)... Accordingly, the display does not capture them...

treated, just need to replace tightening resistors, in the original they cost 10 kOm
I changed them to 1 KOM and everything worked even on firmware from SD1306
As a result, you need to change the resistors R3 R4 cm photo above ...

in the display at 0.96" I had 4.7k Om resistors, and in 1.3" 10k
this refinement may be relevant for other displays with the i2c bus. Who doesn't have the display on the soldering board...

firmware (display on i2c bus fee 2.1S) !!!
If it costs a display of 0.96 you can safely stick 1.3" everything should start,
The only downside is the strip on the side
+
avatar
+2
Well done, sorted out
If it costs a display of 0.96 you can safely stick 1.3" everything should start,
The only downside is the strip on the side
and the strip is treated with firmware on the appropriate firmware (pancake - oil oil)
that's what this review was about.
+
avatar
  • limoncn
  • 12 апреля 2018, 13:06
0
By the way, who came across batteries for a blowtorch clock for the money charged?
+
avatar
+2
Do you have that lithium elements of frenzied money worth?
+
avatar
+2
caught on Tao
Right here
+
avatar
  • oleg_s
  • 12 апреля 2018, 18:11
+1
Offer the seller $0.99, less eBay will not give
=======================================
ebay.com/itm/262871263237
ebay.com/itm/172360411926

Or five grand for $3.50.
====================
aliexpress.com/item/Notebook-BIOS-CMOS-battery-laptop-battery-CR2032-motherboard-battery-with-wire-3V/1224880471.html
+
avatar
  • klarus
  • 11 января 2019, 22:33
0
Thank you so much, good man!

+
avatar
+2
I managed to run a two-inch display

P.S. I apologize for the upside-down picture, it's the trouble of the phone
+
avatar
  • Kembrik
  • 12 апреля 2018, 20:55
+2
The Chinese, too, suffer megalomania.

+
avatar
+1
Where's the picture from? There is no mania, at 0.9 or 1.3 all shallow, when the station is away from the workplace, you need to be distracted from work. On the big screen, everything is visible with lateral vision without being distracted.
That's my opinion.
+
avatar
  • Kembrik
  • 12 апреля 2018, 21:13
+1
From the Chinese chat where the author of the station sits.
+
avatar
+1
I didn't get there, I guess there's a lot more interesting to eat.
The Chinese do not sell until stations with large screens just because of the price, 2.42" costs $20 3.15" -$35. As soon as the price drops, the Xger will push the station with 2"
+
avatar
  • limoncn
  • 13 апреля 2018, 09:21
0
About the displays...
there's still a good old lcd 128x64 on the controller st7290 large)) 128x64
SPI management, though not OLED... for $5.6 only on these firmware it will not start ...
+
avatar
+1
Chinese boy will not do firmware under all possible screens, and without sources we can use existing or write firmware. With sleep driver for board 2.0 already has work to do
+
avatar
  • Kvi
  • 14 апреля 2018, 16:20
0
Then it's better to aliexpress.com/item/1-8-Inch-128-160-Serial-SPI-TFT-Color-LCD-Module-128x160-Display-ST7735-With-SPI/32854739411.html
In general, the price - a penny. That's just who can firmware under such make?
+
avatar
+1
this one is not good, it has a different permission, it needs to redo all the graphics
+
avatar
  • limoncn
  • 15 апреля 2018, 11:45
0
How will he behave in the bright light? there's no glare?

To stick another display
need a software converter to do on an additional MK

maybe there is such an arduino...
+
avatar
0
Good afternoon! If it is not a secret how you did it and where the display was taken.
With Respect!!!
+
avatar
+1
it's a question to whom?
+
avatar
0
To Alex7even.
+
avatar
+1
If this question is addressed to me, it turned out after pulling 4.7k to the bus, added a linear stabilizer on the 5C, filtered the power. The screen was taken on the ebei, but you can take anywhere on the controller ssd1309. It is necessary to sew a stone for the screen 0.96.
Such screens exist spi and i2,c for versions 2.0 with a screen 0.96 spi can also install such a screen. But he won't fit into the staff corps any more.
+
avatar
0
Thank you for the full answer!!!
It's a 2.42" screen ??? And you can put 1.54" ???
+
avatar
+1
I've got 2.42." If the controller is ssd1309, it should work.
+
avatar
+1
Stitching stone should be for the screen 0.96
It is more logical to pour the firmware under the display 1.3 Perhaps and there will be no strip which is in the middle of the display
+
avatar
+1
My screen didn't even put the trash out on the firmware for 1.3"
P.S. Stripe in 2 pixels from the left edge, but not as not in the middle
+
avatar
+1
My screen didn't even put the trash out on the firmware for 1.3
What firmware was it?

left, but not like not in the middle
The photo is yours, both over me so strip down the middle.

+
avatar
+2
The firmware is poured into the stone for ssd1306. These strips are not garbage, it is the frequency of the frame.
I couldn't do a normal picture, out of 10 frames in the photo you can see the horizontal running lane or toss in a few pixels.
+
avatar
0
Good evening Alex. I purchased 2.42 eds, but can't get on I2c. Could you share the display connection scheme???
Respectfully Dmitri!
+
avatar
+1
There is no scheme. you need to transfer the screen to the I2C bus and provide the necessary power.
P.S. I in March connected from 5B. it didn't work on stability. need to make a stabilizer on 3.3B 1A, from the whole crazy scheme of Chinese origininala I refused in favor of a converter for combo, and for T12 made a stabilizer on LM317
+
avatar
+2
That's what I did.





+
avatar
+1
Great turned out, but the photo is better to paste with the PC ;-)
+
avatar
+1
I'm sorry.
+
avatar
+3
That's cool.
I've muddied my body, but I don't know what's better to make a glass out of
+
avatar
+1
plex (orgglass)
+
avatar
0
We don't sell small pieces (((and I would like to find something toned.
+
avatar
+3
If it's hopeless, the box from the CD, you can even color
+
avatar
+2
You can sink with a car...
+
avatar
+3
You can boil the plexus in the ed, the green, cheap and angry.
+
avatar
+2
Maybe it'll help. Bought once on the occasion of ND8 10pc. I'm not steaming anymore. The truth in some crafts is dark and I would like ND4, but especially buy laziness.
+
avatar
+3
Maybe it'll help.
Piece of choice.
+
avatar
+2
It turns out to be expensive, and paid delivery does not please ...
+
avatar
+1
It's a lot expensive.
No question, 2 yuan will suit. ;)
+
avatar
+2
class, 2 yuan, $0.32 - just a balm per capita
excellent price
+
avatar
+1
In Russia, free, bought for a trial 1 piece. On tao of course cheaper, but it is unknown when I will collect a parcel there.
+
avatar
+2
With a picture of what happened in the end ;-)
+
avatar
+2
Yes
+
avatar
+1
Can I take a real picture? Processed normally? How thick?
+
avatar
+2
Processed normally? How thick?
The dimensions are 8.4 cm wide x the height of 9.5 cm x thickness 0.2 cm, the material is plexiglass. On Ali write resin is not glass, it will not be difficult to process.
+
avatar
+1
Thank you
+
avatar
+3
The more solid it is than the plexiglass. I cut a cutter in a few passages, then break. The edges naturally need to be ennobled with a fine skin. Specially now arranged a photo shoot, because the shoemaker without boots. That is, to order I make with glasses, and for myself laziness, now cut the glass under the blowtoral station. Also shown is a fan timer with a green indicator. Let me remind you, the glass is ND8.
Photos
+
avatar
+2
The pictures don't pull up, they don't open
+
avatar
+2
Man... The editing period has already expired. I can re-download without a spoiler, there are 7 photos.
+
avatar
+1
+
avatar
+3
I'm sorry for the quality of the photo, the hand is shaking after yesterday. It is 1.8mm thick.
+
avatar
  • Raimund
  • 18 апреля 2018, 10:20
0
I made a mistake. I would like to run a dual OLED STM32 controller with a new firmware. Now he's dead.

Can anyone send the right firmware?
I took pictures of the controller before I flashed it. I hope someone can help me.

+
avatar
+2
Can anyone send the right firmware?
This is you to Denis aka salamatin
There is no firmware in the public domain!
And why did you decide to sew it?
+
avatar
0
Why send to Denis? All firmware is available here!
+
avatar
+2
Why send to Denis? All firmware is available here!
Because a man needs a firmware for a 2v1 combo and it doesn't ;)
firmware "smd rework"
This firmware is for the hairdryer.
+
avatar
0
Yes, I'm blunt
+
avatar
  • Raimund
  • 19 апреля 2018, 08:21
0
In hindsight, it was a mistake. After this event is always wiser.
+
avatar
+1
firmware is posted on Google and Yandex discs, links in the article
+
avatar
0
In the hat of the theme there is a link to Yandex disc, Google drive, there lies firmware "smd rework"
+
avatar
+1
These are my references to my CDs - there's no firmware for Combo 2v1
+
avatar
+5
+
avatar
+2
Thank you, I missed this firmware. Now I think it's worth checking it on the calculator.
+
avatar
0
The firmware checked...
Kay Gene from the audience does not fit to her... And the weirdness she issues ID is not like the firmware soldering the same process
+
avatar
+1
Thank you, come in handy, q in reputation ;-)
+
avatar
  • Raimund
  • 19 апреля 2018, 08:30
0
@Alex7even thanks for the new firmware. The controller can be restarted.
It seems to be working well.
+
avatar
+1
Alex7even
Did you re-stitch your combo?
keys required a new firmware, keygen-online approached?
+
avatar
+2
Stitched, everything is stored in eeprom, activation is not needed
+
avatar
  • Raimund
  • 19 апреля 2018, 23:45
+2
I can confirm that. No key was required after the key flashing.
+
avatar
+3
Alexander, add a combo firmware to your drives, please. I want to be in one place.
+
avatar
+1
Added to both drives, the iOS folder has been renamed "T12 q hairdryer q Combo 2v1 on STM32 firmware"
Check that there is access and there is this proshika
+
avatar
+1
These are my references to my CDs - there's no firmware for Combo 2v1
;-)
now there is
+
avatar
  • caticus
  • 19 апреля 2018, 17:01
+1
Does anyone know which pressure sensor should be installed in combo 2v1 to launch a tin pump?
+
avatar
+2
I didn't see a hint of such sensors on the diagram. The suction is connected in the soldering chain, there are no other co-ations.
If there is indeed a pressure sensor, then in place of the thermopara you can measure the analog signal, instead of the vibrik - discrete
Share your thoughts, I'm also interested in this topic.
+
avatar
  • caticus
  • 19 апреля 2018, 17:42
+4
divide: The vacuum hose sits on this sensor at one end

There is a place on the board, but not unpacked

The sensor looks like this.

but to find out what he has tth well or brand/model
+
avatar
  • Kembrik
  • 19 апреля 2018, 18:47
+5
MpXA61115AC6U is mentioned in the documentation for the tin pump.

https://www.nxp.com/docs/en/data-sheet/MPXA6115A.pdf
+
avatar
  • caticus
  • 19 апреля 2018, 18:55
0
thank you for the information, and what kind of tin pump is it about?
+
avatar
  • Kembrik
  • 19 апреля 2018, 19:04
+4
I think it's clear where the tin pump boards are and where the tool itself is.



+
avatar
  • caticus
  • 19 апреля 2018, 19:11
0
Got it. Thank you.
+
avatar
  • Raimund
  • 20 апреля 2018, 09:32
+2
The pressure sensor is also supported by Combo 2v1?


+
avatar
  • caticus
  • 21 апреля 2018, 11:11
+2
When you select the N1-10 stinger on the connector contacts, the connector appears 24v.


pressure sensor ordered here

+
avatar
+1
pressure sensor ordered
What kind of pump will it be?
+
avatar
  • caticus
  • 21 апреля 2018, 15:58
0
I don't want to give $40-plus for the pump. I'll do it myself.
+
avatar
+2
I'll do it myself
Looked after for vacuum tweezers like that for $13
+
avatar
+2
There was on hand a display of 1.3 i2c and an old solder with 0.96 spi, crossed hedgehog with rhino)))

I ploughed the 1.3 display into a 0.96 fee and stitched (for the first time in my life)
+
avatar
  • Sascha
  • 02 мая 2018, 06:29
+2
MPXA6115AC6U is not suitable for Combo 2-in-1.
SOP footprint, Case 482 is too big!

Use the MPXHZ6115AC6U, SSOP Footprint, Case 1317A. That fits 100% ;-)
+
avatar
0
I'm interested... Can I save the station settings and download them after re-stitching them? because after the firmware everything is zeroed out
+
avatar
+1
And there are so many settings to rule?
set up 5 presets, gorst sting to calibrate on the new - cases then
+
avatar
0
Well so yes) when yesterday flooded 2.12 there was a thought about reducing the movements)
+
avatar
+2
I'm interested... Can I save the station settings and download them after re-stitching them?
It is possible to count before the firmware of EPROM, then pour back ;) But... there may be surprises with the new firmware, so it's better as said sancho1971
+
avatar
0
OK)
+
avatar
0
I have a question on soldering iron on the 2.1S board
today gathered to the end of the clone of the Chinese
when calibrating the BC2 sting at a top of 444 degrees,
The readings of the theme (on the OLED display) dangle between 350-450 degrees, and at the very regret the temperature dangles...
In the handle between the q and - there is a conder...
Who had a thread like that?
OU costs MCP6022 (with ali)
+
avatar
0
power supply at 24B 100 W
+
avatar
0
I didn't have that kind of hesitation.
Try with another sting
+
avatar
+2
Before calibrating the sting you need to "fry"
+
avatar
+2
We have become an affordable universal calculator from Denis Nick Salamatin, which can generate any codes from soldering controllers on STM32_OLED, generating capabilities following: a soldering controller, a hairdryer controller and a combo controller.
I will tell you right away not for the public, the whim is not mine but the author, we will only help and distribute the codes to all who will ask, so write to whom what you need.
+
avatar
  • sawa13
  • 16 февраля 2019, 01:55
-1
Click for more: 4E42 ID2: DBCF
+
avatar
  • noss
  • 11 июля 2018, 14:10
0
Guys, help...
My brain is already boiling.
The fee -
ru.aliexpress.com/item/STM32F103C8T6-ARM-STM32-Minimum-System-Development-Board-Module-For-Arduino/32278016818.html?src=google&albslr=201159365&isdl=y&aff_short_key=UneMJZVf&source=%7Bifdyn:dyn%7D%7Bifpla:pla%7D%7Bifdbm:DBM&albch=DID%7D&src=google&albch=shopping&acnt=768-202-3196&isdl=y&albcp=1418125144&albag=53860669137&slnk=&trgt=296303633664&plac=&crea=ru32278016818&netw=g&device=c&mtctp=&aff_platform=google&gclid=CjwKCAjw1ZbaBRBUEiwA4VQCIfFFX0G-nm9RDFjProtnTN9c06BvCvxaSxgGQ-93CM0Ii0GKHbW_rxoC1WsQAvD_BwE&gclsrc=aw.ds

I can't activate, I've connected the displ, the encoder, the memory. memory sits on A1 (11) and A0 (10)
He writes that the code is not correct.
ID1:8F2A
ID2:6209
RG1:C6D9
RG2:8426
yadi.sk/d/Smnw7FvR3J7TFx firmware - T12_v.2.1S_OLED0.96
Tried different stm F103C8T6 (couple) the same picture.
+
avatar
0
If the ID is the right one, the codes are correct
+
avatar
  • noss
  • 11 июля 2018, 14:26
0
Such, what could be the problem? Is the industry involved in this matter? Do you need it for a password?
+
avatar
+1
Is the industry involved in this matter? Do you need it for a password?
of course it participates, it keeps registration codes.
+
avatar
  • noss
  • 11 июля 2018, 15:09
0
+
avatar
0
the scheme is drawn from the original board, it has already been collected...
+
avatar
0
I had such until I put atmel eeprom nothing happened!
+
avatar
0
Folks, tell me. Since then the firmware code for different types of encoders has already been changed... is it possible to somehow make a way out of hibernation into a working alternative? For example, I have a place where you can place the station (2.1S by the way) is not, stands on the stand for the stake in the table ;) wildly uncomfortable run her with encoder every time she falls asleep. Let's say there 3.5 times a pen to shake, such?
And, yes, another question - I took a full designer from the Xger (the boos forgot the answer from the connector to put :D), again luto delivers that the staff BP is not so warmed even in slip-fashion, where there is nothing to consume. Has anyone treated that?
+
avatar
0
For example, I have a place where you can place the station (2.1S by the way) is not, stands on the stand for the stake in the table ;) wildly uncomfortable run her with encoder every time she falls asleep. Let's say there 3.5 times a pen to shake, such?
It is you need either the developer to write to the Chinese forum, or a separate button parallel to the encoder button somewhere on the table takeaway do
staff BP is not so warmed even in slip fashion
what kind of BP, there are at least 3 versions. Those that I have do not warm up much...
+
avatar
0
It is you need either the developer to write to the Chinese forum, or a separate button parallel to the encoder button somewhere on the table takeaway do
I had this idea, I'm getting closer to the pedal.
what kind of BP, there are at least 3 versions. Those that I have do not warm up much...
Here's this one:
1
+
avatar
0
I don't know how he behaves. . . .
Bp should not be basking in slip-fashion, there is nothing to bask in. Consumption of the fee - a penny...
+
avatar
0
That's what I'm talking about. But it warms up, the dog... Dishman pyrometer with Ali has not yet got, but I will say that the finger on them can be kept, but not long even after 5 minutes of downtime
+
avatar
  • noss
  • 14 августа 2018, 19:22
0
The V2.00 board can be stitched with a firmware - T12_v.2.1S_OLED1.3 or T12_v.2.0S_OLED1.3 in what differences?
+
avatar
+1
1 - Why? Firmwares are functionally identical
2 - from 2.1S can not be, the display is connected in another way. 2.0S is theoretically possible, but I haven't tried...
I have everything on the gugul disk and for 2.0 (2.00, 2.01) the same way. Don't t tempt fate, take your family
+
avatar
  • h0per
  • September 17, 2018, 5:44 p.m.
0
I wrote a comment. He's stuck in the middle.
Tell me, do you have any ideas about such a shod?

mysku.ru/blog/taobao/48640.html#comment2805181
+
avatar
0
Hello.
Tell the SPD0301 controller is compatible with ssd1306, ssd1309 or sh1106. I want to put a 1.54 inch screen on the station v2.1S, and on AliExpress screens 1.54 inches with the i2c bus only on the controller SPD0301. I can't find anything on the Internet about this controller.
+
avatar
  • deminrv
  • October 1, 2018, 8:12 p.m.
0
Tell me more who can order with your order with Taobao screen 1.54 inches (white) on the i2c bus and the controller SSD1309 (https://cn.shopotam.ru/taobao/549147840420-item.html). I just live in LNR and I can't, and I'll put the money on the card.
+
avatar
+1
write in person
+
avatar
0
Hello.
Replaced on the ve2.1S STM32 OLED1.3" soldering station with OLED1.54" with white font. Stood in the back of the aluminium body KSGER (the front panel is native thin aluminum), only had to bite the clippers gently to bite off the bottom of the display board. The only thing it is not as bright as OLED1.3" installed by the seller, may burn out less will.
+
avatar
  • alzikra
  • 04 января 2019, 15:11
+1


Introducing... I am from Indonesia. Please help if anyone can help my problem. Thank you before.

Controller KSGER STM32. Ver 2.1s
+
avatar
  • Kembrik
  • 04 января 2019, 15:36
+1
RG1:D3CB
RG2:882F
+
avatar
  • ivanhit
  • 09 февраля 2019, 12:05
0
I salute everyone. Recently came the station KSGER from the same store. During the check found glitches. When turning the handle of the encoder, left slyp, or right. Tried to re-ask, helped but partly. Slip and bust began to work when the controller is turned on with a probability of 100 percent some time, later, when the chip warms up, the bust stops working altogether, and the slip is already triggered with a probability of 50 percent. But that's not the point. The Chinese said his engineer, says the problem is in the voltage regulator SE8533. I didn't notice anything special on the date, I found an analogue in the city. But he's at 3.6pc. Friends said that it seems not very critical. Try. I've been in a good place. The controller didn't start at all. The old one was drunk back, the controller turned on, but now doesn't see the sting at all. The soldering iron was ringing. It seems that even called all a hundred touches on the food sting, then also seems to work. But why the chip does not see the sting I can not understand.
Iron 2.0
+
avatar
+2
problem with the bust is already known, start reading from here and down the text, the truth of the comments is a little out of chronology, but I think I'll sort it out

about that station does not see the sting then check the U3 operating room
Googled
STM32_T12_oled_v2.0.jpg, you may have differences and other numbering of items, but the essence is the same
+
avatar
  • ivanhit
  • 09 февраля 2019, 16:04
0
Thank you for the answer. I was just looking at the operating room. I think I even found it. The A36 is written on it. And judging by the scheme just befriends the LED. Now the question is, does it immediately run to change or check it as it is possible on the board? Unfortunately, I'm just learning to be an electronics engineer. Please help.
+
avatar
  • ivanhit
  • 09 февраля 2019, 16:36
0
While waiting for a response from you, came across the fact that the person was having the same problem with the voltage stabilizer. In my case, it's just yu5. Maybe tell you what are the analogues and what it is best to replace. By the way, he also warms up.
+
avatar
  • ivanhit
  • 09 февраля 2019, 17:28
0
The capacitor was under fire. There really were problems with Bost and slip. You shouldn't have sloged the regulator. Now I'm looking for something to plough the operating room.
+
avatar
+1
Look at the scheme of the name of this operating room, there seem SGM8551XN should stand
that's the analogues and look for
there is a branch on the radio-cat, there they themselves worked out a fee and picked up a set that anyone had, remember in the evening, to throw a link
+
avatar
  • ivanhit
  • 09 февраля 2019, 17:59
0
It's evening, no three minutes, 19 minutes. I've got an A36. Found the datechi OPA336 kind of similar to what's worth and you have in the scheme. I'm going to call the store and ask for it. There are no regulators. Now the broken boards look, maybe I will find where to sleep.
+
avatar
  • ivanhit
  • 11 февраля 2019, 10:19
0
Hello. It's a question of that nature. The fact is that when the solder was with glitches but worked more or less that when disconnecting the soldering from the station or pulling the sting, the inscription of the error blinked alternately changing and showing the temperature. Now there is no such thing, it just burns the error. This may somehow indicate an operating room or a probability of not 100 percent. The thing is, I kind of found a similar amplifier. But nothing has changed. I decided to completely reject the amplifier. It's the same. Silence. The error is on fire and that's it. Only on the menus you can climb. Is it possible to diagnose this somehow? I don't know if I'm going to give you a 3.3 volt to the chip entry or something like that? to simulate a connection.

Just why I'm asking that. Judging by the diagram, the heater itself is separated from the sensor and the position sensor. Therefore, at least the position dates and the temperature sensor of the handles kind of have to work. Or am I wrong? I've just ordered 400p from China, and I'm thinking about whether to risk it with this amplifier. The operating room will come the one that is needed and the problem will not be in it. 400p per smark.
+
avatar
+2
The heater itself is separated from the sensor
Wrong.
The heater is connected to the thermopapar sequentially, and the thermo-disisttor in the handle stands for other purposes.

I don't know if I'm going to give you a 3.3 volt to the chip entry or something like that? to simulate a connection.
too much, try 1-1.5 volts.
+
avatar
+1
I didn't notice anything special on the date, I found an analogue in the city. But he's at 3.6pc. Friends said that it seems not very critical. Try. I've been in a good place. The controller didn't start at all.
It was probably different.
mysku.ru/blog/aliexpress/62126.html#comment2965774

and on the subject, what was found out.
mysku.ru/blog/aliexpress/62126.html#comment2973424
mysku.ru/blog/aliexpress/62126.html#comment2998951
+
avatar
  • ivanhit
  • 11 февраля 2019, 11:18
0
Thank you for the answer. According to the first report. I was referring to the soldering pen heating sensor. That the temperature of the sting is measured by the same pin as the heating itself I know. I just can't figure out if the chip's entrance burned down or if I have a non-working operating room. He's always on the way out. The soldering controller stubbornly does not see. Constantly static burns error. He's not blinking. It does not measure the temperature of the handle. In general, the snuul does not react.
On a glitch with a bead and a slip, solved the issue by soldering the conder to the feet of the screen as the video was.
+
avatar
+1
Well, there are two options, or smm32 or ou.
+
avatar
  • ivanhit
  • 11 февраля 2019, 12:09
0
St32 is a hundred-year-old marking. Anything can stand there. That's why I sin on her. Him. So I think you can refuse to buy a bunch of operating ins? They haven't sent me out yet.
+
avatar
  • ivanhit
  • 11 февраля 2019, 11:24
0
That's a recent noticed change at the operating room entrance. With a connected soldering iron 11milivolt, with 500-600 disconnected somewhere milvolt. But at the same time on the output of the operating room constantly 3.3volt, which goes to the chip. And again, the screen burns statically. There is no switching from the inscription of the error to the temperature and the top. But at the same time I can safely climb the menus. And turn on both the bust and the slip.

Vo, the soldering shake responds. That's what goes off to the stand-and-go, and goes out when shaking

yadi.sk/i/c9uFqtzmP32W8w
+
avatar
+1
If
При подключенном паяльнике 11миливольт, при отключенном 500-600 гдето миливольт. Но при этом на выходе операционника постоянно 3.3вольта, что идет на чип.

that probably it is the OU dead, when the input voltage changes, the output should be the voltage proportional to the input (depending on the coef-ta gain), and you have a constant 3.3B
+
avatar
  • ivanhit
  • 11 февраля 2019, 13:57
0
And how to understand that the screen remains static? On the reviews at all the inscription error blinks constantly.

It's funny, but things have changed. Now, after the break-up, a couple of times there was a ploughing operating room, and now on the way out the situation is changing. When you connect the soldering iron at the exit, there is almost nothing as much as at the entrance. So still, I think that entrance burned down at the chip. Again, about super Chinese, without a name.
+
avatar
0
Folks, please share the native Chinese firmware 2.09 under iron 2.0 with a display of 1.3."
+
avatar
0
And how?
You don't think it's readable. . . .

what does 2.11 and 2.12 not suit???
+
avatar
0
2.11 and is worth it, suits. And 2.09 just flew off when I tried to count it... But for the collection, so to speak, and its hunt to have.
+
avatar
0
Well, it is you with the afftor (Chinese) need to communicate, if he wants (which I doubt very much) will give

Но для коллекции, так сказать, и ее охота иметь. 

And what's so special about it???
+
avatar
  • sawa13
  • 16 февраля 2019, 02:08
0
please tell us.
+
avatar
0
Look at the fox
+
avatar
  • BarsSc
  • 05 марта 2019, 16:00
0
Hello. Die on a solder from static. I've been drinking a new mc, I've re-asked for a code, please tell me. ID1: EE50 ID2: 417A.
+
avatar
  • Kembrik
  • 05 марта 2019, 16:22
+2
RG1: 9043
RG2: CDB9
+
avatar
  • BarsSc
  • 05 марта 2019, 16:31
0
Thank you very much, everything has worked!
+
avatar
0
Tell me, please. ID1: E830 ID2: 83B2
+
avatar
0
If for a soldering station, here's
A3E3
AC1C
+
avatar
0
Hello world!
I decided to collect a soldering iron, ordered a pen (set 9501) and a couple of stings (cartridges).
The controller want to collect himself, available stm32f103c8t6 it is suitable?
Does anyone already have a divorced print? Can you share it?
+
avatar
0
Look and ask.
+
avatar
0
I've already found the rescue.
+
avatar
  • valic1
  • 12 апреля 2019, 14:13
0
ksger ver 2.1s invert something can be fixed or $50 in the trash
+
avatar
+1
Why go straight to the trash?
The controller at least works and displays an error - that's a good thing.
I had a similar mistake when I was short in regret, put another, everything works great. This error was met with other users, read the forum on the radio cat,there on the last 2-3 pages discussed this problem ...
+
avatar
  • valic1
  • 12 апреля 2019, 20:38
+1
Tried 100% working, the same!
Maybe the problem is the pen of the soldering iron itself?
+
avatar
+1
look at my previous review, there's a link at the beginning of this
There's a pen-connection scheme and check what you've got.
And yet, you bought ready -- as I understood)
Take the GX12-5 connector and see if the ration is insulated or not.
I used to do it when I was collecting mine.

From the store usually comes so

Maybe somewhere short
+
avatar
+1
there was such a mistake when experimenting with 3.3V
filed 3.3, and 24 forgot to file.
+
avatar
  • valic1
  • April 13, 2019, 10:36 p.m.
0
Try!
+
avatar
  • Ltss
  • 21 мая 2019, 12:48
0
No, it's the controller, the STM itself. There was such a problem. I've got a 1.5 month controller worked out, and I'm out. Checked the missing, all the stresses, the pulsations of the oscillograph - all the norm. Sin on EEPROM. Replaced. Useless. Then I checked the power chain . . . - the norm. Checked the operating room - plugged the handle and heated the sting with another soldering iron. The operating room was working, and he was giving out his own Ku 249. Contacted Lisa Cian, the manager, though not immediately, but another controller sent. A couple of weeks ago, I got it.
+
avatar
  • vstek85
  • August 1, 2019, 9:34 p.m.
0
Hello. Tell me, please. The station required ID1 and 2 at the next turn on. With generated in the program, writes failed to save the registration code. Changed firmware, writes the same ID and also does not accept. ver 2.1s. I'm grateful in advance.
+
avatar
0
maybe EEPROM died
+
avatar
  • Vldik00
  • 05 января 2020, 20:27
0
Please help

ID1: 0000
ID2: 2BC0
RG1: xxxx ??
RG2: xxxx ??
+
avatar
+2
C40D
8A91
+
avatar
0
could you help me?
KSGER STM32 1.3 OLED
HW: 2.00
SW: 2.11
ID1: 4B23
ID2: 5E11
+
avatar
+1
5C1F
449C
+
avatar
0
Thanx for your replay.

Unfortunatelly these code not working. I bought station from KSGER Official Store with sw 2.09. After first power on, station still ask me about activate code. ID1 & ID2 permanently change value every reset ;-( I decide to change soft to 2.11. But problem with activation sw still exist — dont remamber code. Is it possible that eeprom is broken? I could replace eeprom (AT23C32) on the board to another. Maybe it helps? Is it possible flash alternative soft to this station?
+
avatar
0
Do you understand Russian?
there is a radio-cat forum, there they discussed the same problem

eeprom replacement should help
+
avatar
0
thanx for your advise.
Give me codes for for sw 2.11
ID1 4B23
ID2 3401
I will try last time.

Thanx a lot
+
avatar
  • Kembrik
  • 23 февраля 2020, 11:39
+1
RG1:233D
RG2:00D9
+
avatar
0
Well you and nimble ;-)
+
avatar
  • dr-baks
  • 17 января 2020, 22:44
0
Please tell me what it is firmware T12_v.2.00_OLED1.3_enc_mod.hex and what chips it contains.
+
avatar
+1
T12_v.2.00_OLED1.3_enc_mod.hex
this firmware is no different from the base T12_v.2.00_OLED1.3.hex,the only one that has made changes to the work of the encoder. It is used for encoders mounted on the controller board, which the rotation of the axis clockwise leads to a decrease in the values of the set. That is, the work of the encoder is inverted.
There are no other changes.
+
avatar
0
Hello, can't the hercon be screwed here so that the stand is on hold?
+
avatar
0
And who's stopping you, instead of position sensor, put a hercon
+
avatar
0
hindered by the fact that in fact it will not change anything - the station will go into stand mode through the time reared in the settings, and not when installing a soldering pad on the stand.
+
avatar
0
I don't know what it's for???
Put the settings on standby in 1 minute
+
avatar
+1
if in a nutshell then: 1. I want, 2.
and if you want to read my whining then:
I'll hide it under a spoiler.



Of course, you can implement something similar, but I would like to find a more elegant solution, especially since the controller has so many unused legs and hercon is used in a similar station with a hairdryer.
+
avatar
0
soldering iron begins to fall asleep during the ration, of course you can shake it
I got the impression that you have a sensor in the handle or not working properly or is not panicked about the stand
check on these pictures

and check the 01 mode on the menu. Standbythat you have set up there
+
avatar
0
Hello, maybe you and firmware and for STC came across?
I want to see what's inside, the board of quico on stc, or it's felt that the station sees the cooling of the sting much better than "give" when he sees, and you want to twist this "giving" heat in him, if he still sees cooling down.
+
avatar
0
on the quico, and even on stc - not, did not come across
+
avatar
0
Not a quico, just stc?
And in general, what can you say about a piece of code, in different firmware that saw, which is responsible for "giving heat" - reading the temperature with the sting, comparing it with the exposed, and increasing the power supplied.
How is this implemented, good/bad, what is wrong, and how best can this part be implemented?

Only registered and authorized users can comment.


Original